# Fusion power

The Joint European Torus (JET) magnetic fusion experiment in 1991

Fusion power is a proposed form of power generation that would generate electricity by using heat from nuclear fusion reactions. In a fusion process, two lighter atomic nuclei combine to form a heavier nucleus, while releasing energy. Devices designed to harness this energy are known as fusion reactors.

Fusion processes require fuel and a confined environment with sufficient temperature, pressure and confinement time to create a plasma in which fusion can occur. The combination of these figures that results in a power-producing system is known as the Lawson criterion. In stars, the most common fuel is hydrogen, and gravity provides extremely long confinement times that reach the conditions needed for fusion energy production. Proposed fusion reactors generally use hydrogen isotopes such as deuterium and tritium, which react more easily than hydrogen to allow them to reach the Lawson criterion requirements with less extreme conditions. Most designs aim to heat their fuel to tens of millions of degrees, which presents a major challenge in producing a successful design.

As a source of power, nuclear fusion is expected to have several advantages over fission. These include reduced radioactivity in operation and little high-level nuclear waste, ample fuel supplies, and increased safety. However, achieving the necessary combination of temperature, pressure, and duration has proven to be difficult to produce in a practical and economical manner. Research into fusion reactors began in the 1940s, but to date, no design has produced more fusion power output than the electrical power input, defeating the purpose.[1] A second issue that affects common reactions, is managing neutrons that are released during the reaction, which over time degrade many common materials used within the reaction chamber.

Fusion researchers have investigated various confinement concepts. The early emphasis was on three main systems: z-pinch, stellarator and magnetic mirror. The current leading designs are the tokamak and inertial confinement (ICF) by laser. Both designs are under research at very large scales, most notably the ITER tokamak in France, and the National Ignition Facility laser in the United States. Researchers are also studying other designs that may offer cheaper approaches. Among these alternatives there is increasing interest in magnetized target fusion and inertial electrostatic confinement, and new variations of the stellarator.

## Background

The Sun, like other stars, is a natural fusion reactor, where stellar nucleosynthesis transforms lighter elements into heavier elements with the release of energy.
Binding energy for different atomic nuclei. Iron-56 has the highest, making it the most stable. Nuclei to the left are likely to fuse; those to the right are likely to split.

### Mechanism

Fusion reactions occur when two or more atomic nuclei come close enough for long enough that the nuclear force pulling them together exceeds the electrostatic force pushing them apart, fusing them into heavier nuclei. For nuclei lighter than iron-56, the reaction is exothermic, releasing energy. For nuclei heavier than iron-56, the reaction is endothermic, requiring an external source of energy.[2] Hence, nuclei smaller than iron-56 are more likely to fuse while those heavier than iron-56 are more likely to break apart.

The strong force acts only over short distances. The repulsive electrostatic force acts over longer distances. In order to undergo fusion, the fuel atoms need to be given enough energy to approach each other close enough for the strong force to become active. The amount of kinetic energy needed to bring the fuel atoms close enough is known as the "Coulomb barrier". Ways of providing this energy include speeding up atoms in a particle accelerator, or heating them to high temperatures.

Once an atom is heated above its ionization energy, its electrons are stripped away (it is ionized), leaving just the bare nucleus (the ion). The result is a hot cloud of ions and the electrons formerly attached to them. This cloud is known as plasma. Because the charges are separated, plasmas are electrically conductive and magnetically controllable. Many fusion devices take advantage of this to control the particles as they are heated.

### Cross section

The fusion reaction rate increases rapidly with temperature until it maximizes and then gradually drops off. The deuterium-tritium fusion rate peaks at a lower temperature (about 70 keV, or 800 million kelvin) and at a higher value than other reactions commonly considered for fusion energy.

A reaction's cross section, denoted σ, is the measure of the probability that a fusion reaction will happen. This depends on the relative velocity of the two nuclei. Higher relative velocities generally increase the probability, but the probability begins to decrease again at very high energies. Cross sections for many fusion reactions were measured (mainly in the 1970s) using particle beams.[3]

In a plasma, particle velocity can be characterized using a probability distribution. If the plasma is thermalized, the distribution looks like a bell curve, or maxwellian distribution. In this case, it is useful to use the average particle cross section over the velocity distribution. This is entered into the volumetric fusion rate:[4]

${\displaystyle P_{\text}=n_n_\langle \sigma v_\rangle E_{\text}}$

where:

• ${\displaystyle P_{\text}}$ is the energy made by fusion, per time and volume
• n is the number density of species A or B, of the particles in the volume
• ${\displaystyle \langle \sigma v_\rangle }$ is the cross section of that reaction, average over all the velocities of the two species v
• ${\displaystyle E_{\text}}$ is the energy released by that fusion reaction.

### Lawson Criterion

The Lawson Criterion shows how energy output varies with temperature, density, speed of collision, and fuel. This equation was central to John Lawson's analysis of fusion working with a hot plasma. Lawson assumed an energy balance, shown below.[4]

${\displaystyle P_{\text}=\eta _{\text}\left(P_{\text}-P_{\text}-P_{\text}\right)}$
• η, efficiency
• ${\displaystyle P_{\text}}$, conduction losses as energy laden mass leaves
• ${\displaystyle P_{\text}}$, radiation losses as energy leaves as light
• ${\displaystyle P_{\text}}$, net power from fusion
• ${\displaystyle P_{\text}}$, is rate of energy generated by the fusion reactions.

Plasma clouds lose energy through conduction and radiation.[4] Conduction occurs when ions, electrons or neutrals impact other substances, typically a surface of the device, and transfer a portion of their kinetic energy to the other atoms. Radiation is energy that leaves the cloud as light in the visible, UV, IR, or X-ray spectra. Radiation increases with temperature. Fusion power technologies must overcome these losses.

### Triple product: density, temperature, time

The Lawson criterion argues that a machine holding a thermalized and quasi-neutral plasma has to meet basic criteria to overcome radiation losses, conduction losses and reach efficiency of 30 percent.[4][5] This became known as the "triple product": the plasma density, temperature and confinement time.[6]

In magnetic confinement designs, the density is very low, on the order of a "good vacuum". This means that useful reaction rates require the temperature and confinement time to be increased to offset the low density. Fusion-relevant temperatures have been achieved using a variety of heating methods that were developed in the early 1970s, and in modern machines, as of 2019, the major remaining issue is the confinement time. Plasmas in strong magnetic fields are subject to a number of inherent instabilities, which must be suppressed to reach useful times. One way to do this is to simply make the reactor volume larger, which reduces the rate of leakage due to classical diffusion. This is why modern designs like ITER are so large.

In contrast, inertial confinement systems approach useful triple product values via higher density, and have vanishingly small confinement times. In modern machines like NIF, the initial frozen hydrogen fuel load has a density less than water which is increased to about 100 times the density of lead. In these conditions, the rate of fusion is so high that the entire fuel load undergoes fusion in the microseconds it takes for the heat generated by the reactions to blow the fuel apart. Although modern ICF machines like NIF are also extremely large, this is a function of their "driver" design, not an inherent design criterion of the fusion process itself.

### Energy capture

Multiple approaches have been proposed for energy capture. The simplest is to heat a fluid. Most designs concentrate on the D-T reaction, which releases much of its energy in a neutron. Electrically neutral, the neutron escapes the confinement. In most such designs, it is ultimately captured in a thick "blanket" of lithium surrounding the reactor core. When struck by a high-energy neutron, the lithium can produce tritium, which is then fed back into the reactor. The energy of this reaction also heats the blanket, which is then actively cooled with a working fluid and then that fluid is used to drive conventional turbomachinery.

It has also been proposed to use the neutrons to breed additional fission fuel in a blanket of nuclear waste, a concept known as a fission-fusion hybrid. In these systems, the power output is enhanced by the fission events, and power is extracted using systems like those in conventional fission reactors.[7]

Designs that use other fuels, notably the p-B reaction, release much more of their energy in the form of charged particles. In these cases, alternate power extraction systems based on the movement of these charges are possible. Direct energy conversion was developed at LLNL in the 1980s as a method to maintain a voltage using the fusion reaction products. This has demonstrated energy capture efficiency of 48 percent.[8]

## Methods

### Plasma behavior

Plasma is an ionized gas that conducts electricity.[9] In bulk, it is modeled using magnetohydrodynamics, which is a combination of the Navier–Stokes equations governing fluids and Maxwell's equations governing how magnetic and electric fields behave.[10] Fusion exploits several plasma properties, including:

• Self-organizing plasma conducts electric and magnetic fields. Its motions can generate fields that can in turn contain it.[11]
• Diamagnetic plasma can generate its own internal magnetic field. This can reject an externally applied magnetic field, making it diamagnetic.[12]
• Magnetic mirrors can reflect plasma when it moves from a low to high density field.[13]

### Magnetic confinement

• Tokamak: the most well-developed and well-funded approach to fusion energy. This method races hot plasma around in a magnetically confined torus, with an internal current. When completed, ITER will be the world's largest tokamak. As of April 2012 an estimated 215 experimental tokamaks were either planned, decommissioned or currently operating (35) worldwide.[14]
• Spherical tokamak: also known as spherical torus. A variation on the tokamak with a spherical shape.
• Stellarator: Twisted rings of hot plasma. The stellarator attempts to create a natural twisted plasma path, using external magnets, while tokamaks create those magnetic fields using an internal current. Stellarators were developed by Lyman Spitzer in 1950 and have four designs: Torsatron, Heliotron, Heliac and Helias. One example is Wendelstein 7-X, a German fusion device that produced its first plasma on December 10, 2015. It is the world's largest stellarator,[15] designed to investigate the suitability of this type of device for a power station.
• Internal rings: Stellarators create a twisted plasma using external magnets, while tokamaks do so using a current induced in the plasma. Several classes of designs provide this twist using conductors inside the plasma. Early calculations showed that collisions between the plasma and the supports for the conductors would remove energy faster than the fusion reactions could replace. Modern variations, including the Levitated Dipole Experiment (LDX), use a solid superconducting torus that is magnetically levitated inside the reactor chamber.[16]
• Magnetic mirror: Developed by Richard F. Post and teams at LLNL in the 1960s.[17] Magnetic mirrors reflected hot plasma back and forth in a line. Variations included the Tandem Mirror, magnetic bottle and the biconic cusp.[18] A series of well-funded, large, mirror machines were built by the US government in the 1970s and 1980s, principally at Lawrence Livermore National Laboratory.[19] However, calculations in the 1970s demonstrated it was unlikely these would ever be commercially useful.
• Bumpy torus: A number of magnetic mirrors are arranged end-to-end in a toroidal ring. Any fuel ions that leak out of one are confined in a neighboring mirror, permitting the plasma pressure to be raised arbitrarily high without loss. An experimental facility, the ELMO Bumpy Torus or EBT was built and tested at Oak Ridge National Laboratory in the 1970s.
• Field-reversed configuration: This device traps plasma in a self-organized quasi-stable structure; where the particle motion makes an internal magnetic field which then traps itself.[20]
• Spheromak: Very similar to a field-reversed configuration, a semi-stable plasma structure made by using the plasmas' own self-generated magnetic field. A spheromak has both toroidal and poloidal fields, while a field-reversed configuration has no toroidal field.[21]
• Reversed field pinch: Here the plasma moves inside a ring. It has an internal magnetic field. Moving out from the center of this ring, the magnetic field reverses direction.

### Inertial confinement

• Indirect drive: In this technique, lasers heat a structure known as a Hohlraum that becomes so hot it begins to radiate huge amounts of x-ray light. These x-rays heat a small pellet of fuel, causing it to collapse inward to compress the fuel. The largest system using this method is the National Ignition Facility, followed closely by Laser Mégajoule.[22]
• Direct drive: A variation of the ICF technique in which the lasers directly on the fuel pellet. Notable direct drive experiments have been conducted at the Laboratory for Laser Energetics and the GEKKO XII facilities. Good implosions require fuel pellets with close to a perfect shape in order to generate a symmetrical inward shock wave that produces the high-density plasma.
• Fast ignition: This method uses two laser blasts. The first blast compresses the fusion fuel, while the second high energy pulse ignites it. As of 2019 this technique is no longer favored for energy production due to a number of unexpected problems.[23]
• Magneto-inertial fusion or Magnetized Liner Inertial Fusion: This combines a laser pulse with a magnetic pinch. The pinch community refers to it as magnetized liner Inertial fusion while the ICF community refers to it as magneto-inertial fusion.[24]
• Heavy Ion Beams There are also proposals to do inertial confinement fusion with ion beams instead of laser beams.[25] The main difference is that the beam has momentum due to mass, whereas lasers do not. However, given what has been learned using laser devices, it appears unlikely that ion beams can be focussed both spatially and in time to the exacting needs of ICF.
• Z-machine a unique approach to ICF is the z-machine, which sends a huge electrical current through thin tungsten wires, heating them to x-ray temperatures. Like the indirect drive approach, these x-rays then compress a fuel capsule.

### Magnetic or electric pinches

• Z-Pinch: This method sends a strong current (in the z-direction) through the plasma. The current generates a magnetic field that squeezes the plasma to fusion conditions. Pinches were the first method for man-made controlled fusion.[26][27] However, it was later discovered that the z-pinch has inherent instabilities that limit its compression and heating to values far too low for practical fusion, and the largest such machine, the UK's ZETA, was the last major experiment of the sort. Exploration of the problems in z-pinch led to the tokamak design. Later variation on the design include dense plasma focus (DPF).
• Theta-Pinch: This method sends a current around the outside of a plasma column, in the theta direction. This induces a magnetic field running down the center of the plasma, as opposed to around it. The early theta-pinch device Scylla was the first to conclusively demonstrate fusion, but later work demonstrated it had inherent limits that made it uninteresting for power production.
• Screw Pinch: This method combines a theta and z-pinch for improved stabilization.[28]

### Inertial electrostatic confinement

• Fusor: This method uses an electric field to heat ions to fusion conditions. The machine typically uses two spherical cages, a cathode inside the anode, inside a vacuum. These machines are not considered a viable approach to net power because of their high conduction and radiation[29] losses. They are simple enough to build that amateurs have fused atoms using them.[30]
• Polywell: This design attempts to combine magnetic confinement with electrostatic fields, to avoid the conduction losses generated by the cage.[31]

### Other

• Magnetized target fusion: This method confines hot plasma using a magnetic field and squeezes it using inertia. Examples include LANL FRX-L machine,[32] General Fusion and the plasma liner experiment.[33]
• Cluster Impact Fusion Microscopic droplets of heavy water are accelerated at great velocity into a target or into one another. Researchers at Brookhaven reported positive results which were later refuted by further experimentation. Fusion effects were actually produced because of contamination of the droplets.
• Uncontrolled: Fusion has been initiated by man, using uncontrolled fission explosions to ignite so-called Hydrogen Bombs. Early proposals for fusion power included using bombs to initiate reactions.
• Beam fusion: A beam of high energy particles can be fired at another beam or target and fusion will occur. This was used in the 1970s and 1980s to study the cross sections of high energy fusion reactions.[3]
• Bubble fusion: This was a fusion reaction that was supposed to occur inside extraordinarily large collapsing gas bubbles, created during acoustic liquid cavitation.[34] This approach was discredited.
• Cold fusion: This is a hypothetical type of nuclear reaction that would occur at, or near, room temperature. Cold fusion is discredited and gained a reputation as pathological science.[35][36]
• Muon-catalyzed fusion: This approach replaces electrons in diatomic molecules of isotopes of hydrogen with muons - far more massive particles with the same electric charge. Their greater mass results in the nuclei getting close enough such that the strong interaction can cause fusion to occur.[37] Currently, muons require more energy to produce than can be obtained from muon-catalyzed fusion. Unless this is solved, muon-catalyzed fusion is impractical for power generation.[38]

## Common tools

### Heating

Gas is heated to form a plasma hot enough to start fusion reactions. A number of heating schemes have been explored: Radiofrequency Heating A radio wave is applied to the plasma, causing it to oscillate. This is basically the same concept as a microwave oven. This is also known as electron cyclotron resonance heating or Dielectric heating.[citation needed]

Electrostatic Heating An electric field can do work on charged ions or electrons, heating them.[39]

Neutral Beam Injection An external source of hydrogen is ionized and accelerated by an electric field to form a charged beam which is shone through a source of neutral hydrogen gas towards the plasma which itself is ionized and contained in the reactor by a magnetic field. Some of the intermediate hydrogen gas is accelerated towards the plasma by collisions with the charged beam while remaining neutral: this neutral beam is thus unaffected by the magnetic field and so shines through it into the plasma. Once inside the plasma the neutral beam transmits energy to the plasma by collisions as a result of which it becomes ionized and thus contained by the magnetic field thereby both heating and refuelling the reactor in one operation. The remainder of the charged beam is diverted by magnetic fields onto cooled beam dumps.[40]

Antiproton annihilation Theoretically a quantity of antiprotons injected into a mass of fusion fuel can induce thermonuclear reactions. This possibility as a method of spacecraft propulsion, known as Antimatter-catalyzed nuclear pulse propulsion, was investigated at Pennsylvania State University in connection with the proposed AIMStar project.

Magnetic Oscillations[41]

### Measurement

Thomson Scattering Light scatters from plasma. This light can be detected and used to reconstruct the plasmas' behavior. This technique can be used to find its density and temperature. It is common in Inertial confinement fusion,[42] Tokamaks[43] and fusors. In ICF systems, this can be done by firing a second beam into a gold foil adjacent to the target. This makes x-rays that scatter or traverse the plasma. In Tokamaks, this can be done using mirrors and detectors to reflect light across a plane (two dimensions) or in a line (one dimension).

Langmuir probe This is a metal object placed in a plasma. A potential is applied to it, giving it a positive or negative voltage against the surrounding plasma. The metal collects charged particles, drawing a current. As the voltage changes, the current changes. This makes a IV Curve. The IV-curve can be used to determine the local plasma density, potential and temperature.[44]

Neutron detectors Deuterium or tritium fusion produces neutrons. Neutrons interact with surrounding matter in ways that can be detected. Several types of neutron detectors exist which can record the rate at which neutrons are produced during fusion reactions. They are an essential tool for demonstrating success.

Flux loop A loop of wire is inserted into the magnetic field. As the field passes through the loop, a current is made. The current is measured and used to find the total magnetic flux through that loop. This has been used on the National Compact Stellarator Experiment,[45] the polywell[46] and the LDX machines.

X-ray detector All plasma loses energy by emitting light. This covers the whole spectrum: visible, IR, UV, and X-rays. This occurs anytime a particle changes speed, for any reason.[47] If the reason is deflection by a magnetic field, the radiation is Cyclotron radiation at low speeds and Synchrotron radiation at high speeds. If the reason is deflection by another particle, plasma radiates X-rays, known as Bremsstrahlung radiation. X-rays are termed in both hard and soft, based on their energy.

### Power production

It has been proposed [48] that steam turbines be used to convert the heat from the fusion chamber into electricity. The heat is transferred into a working fluid that turns into steam, driving electric generators.

Neutron blankets Deuterium and tritium fusion generates neutrons. This varies by technique (NIF has a record of 3E14 neutrons per second[49] while a typical fusor produces 1E5–1E9 neutrons per second). It has been proposed to use these neutrons as a way to regenerate spent fission fuel [50] or as a way to breed tritium using a breeder blanket consisting of liquid lithium or, as in more recent reactor designs, a helium cooled pebble bed consisting of lithium bearing ceramic pebbles fabricated from materials such as Lithium titanate, lithium orthosilicate or mixtures of these phases.[51]

Direct conversion This is a method where the kinetic energy of a particle is converted into voltage.[52] It was first suggested by Richard F. Post in conjunction with magnetic mirrors, in the late sixties. It has also been suggested for Field-Reversed Configurations. The process takes the plasma, expands it, and converts a large fraction of the random energy of the fusion products into directed motion. The particles are then collected on electrodes at various large electrical potentials. This method has demonstrated an experimental efficiency of 48 percent.[53]

## Records

Fusion records have been set by a number of devices. Here are some:

### Q

The ratio of energy extracted against the amount of energy supplied. This record is considered to be set by the Joint European Torus (JET) in 1997 when the device extracted 16 MW of power.[54] However, this ratio can be seen three different ways.

• 0.69 is the actual point in time ratio between ”fusion power” and actual input power in the plasma (23 MW).
• 0.069 is the ratio between the “fusion” power and the power required to produce the 23MW input power (essentially it takes into account the efficiency of the NB system).
• 0.0069 is the ratio between the “fusion” power and the total peak power required for a JET pulse. This takes into account all the power from the grid plus the one from the two large JET flywheel generators.[citation needed]

### Runtime

In Field Reversed Configurations, the longest run time is 300 ms, set by the Princeton Field Reversed Configuration in August 2016.[55] However this involved no fusion.

### Beta

The fusion power trends as the plasma confinement raised to the fourth power.[56] Hence, getting a strong plasma trap is of real value to a fusion power plant. Plasma has a very good electrical conductivity. This opens the possibility of confining the plasma with magnetic field, generally known as magnetic confinement. The field puts a magnetic pressure on the plasma, which holds it in. A widely used measure of magnetic trapping in fusion is the beta ratio:

${\displaystyle \beta ={\frac }}={\frac T}{(B^/2\mu _)}}}$ [57]

This is the ratio of the externally applied field to the internal pressure of the plasma. A value of 1 is ideal trapping. Some examples of beta values include:

1. The START machine: 0.32
2. The Levitated dipole experiment:[58] 0.26
3. Spheromaks: ≈ 0.1,[59] Maximum 0.2 based on Mercier limit.[60]
4. The DIII-D machine: 0.126[citation needed]
5. The Gas Dynamic Trap a magnetic mirror: 0.6 [61] for 5E−3 seconds.[62]
6. The Sustained Spheromak Plasma Experiment at Los Alamos National labs < 0.05 for 4E−6 seconds.[63]

## Confinement

Parameter space occupied by inertial fusion energy and magnetic fusion energy devices as of the mid 1990s. The regime allowing thermonuclear ignition with high gain lies near the upper right corner of the plot.

Confinement refers to all the conditions necessary to keep a plasma dense and hot long enough to undergo fusion. Here are some general principles.

• Equilibrium: The forces acting on the plasma must be balanced for containment. One exception is inertial confinement, where the relevant physics must occur faster than the disassembly time.
• Stability: The plasma must be so constructed so that disturbances will not lead to the plasma disassembling.
• Transport or conduction: The loss of material must be sufficiently slow.[4] The plasma carries off energy with it, so rapid loss of material will disrupt any machines power balance. Material can be lost by transport into different regions or conduction through a solid or liquid.

To produce self-sustaining fusion, the energy released by the reaction (or at least a fraction of it) must be used to heat new reactant nuclei and keep them hot long enough that they also undergo fusion reactions.

### Unconfined

The first human-made, large-scale fusion reaction was the test of the hydrogen bomb, Ivy Mike, in 1952. As part of the PACER project, it was once proposed to use hydrogen bombs as a source of power by detonating them in caverns and then generating electricity from the heat produced, but such a power station is unlikely ever to be constructed.

### Magnetic confinement

Magnetic Mirror One example of magnetic confinement is with the magnetic mirror effect. If a particle follows the field line and enters a region of higher field strength, the particles can be reflected. There are several devices that try to use this effect. The most famous was the magnetic mirror machines, which was a series of large, expensive devices built at the Lawrence Livermore National Laboratory from the 1960s to mid 1980s.[64] Some other examples include the magnetic bottles and Biconic cusp.[65] Because the mirror machines were straight, they had some advantages over a ring shape. First, mirrors were easier to construct and maintain and second direct conversion energy capture, was easier to implement.[8] As the confinement achieved in experiments was poor, this approach was abandoned.[citation needed]

Magnetic Loops Another example of magnetic confinement is to bend the field lines back on themselves, either in circles or more commonly in nested toroidal surfaces. The most highly developed system of this type is the tokamak, with the stellarator being next most advanced, followed by the Reversed field pinch. Compact toroids, especially the Field-Reversed Configuration and the spheromak, attempt to combine the advantages of toroidal magnetic surfaces with those of a simply connected (non-toroidal) machine, resulting in a mechanically simpler and smaller confinement area.

### Inertial confinement

Inertial confinement is the use of rapidly imploding shell to heat and confine plasma. The shell is imploded using a direct laser blast (direct drive) or a secondary x-ray blast (indirect drive) or heavy ion beams. Theoretically, fusion using lasers would be done using tiny pellets of fuel that explode several times a second. To induce the explosion, the pellet must be compressed to about 30 times solid density with energetic beams. If direct drive is used—the beams are focused directly on the pellet—it can in principle be very efficient, but in practice is difficult to obtain the needed uniformity.[66] The alternative approach, indirect drive, uses beams to heat a shell, and then the shell radiates x-rays, which then implode the pellet. The beams are commonly laser beams, but heavy and light ion beams and electron beams have all been investigated.[67]

### Electrostatic confinement

There are also electrostatic confinement fusion devices. These devices confine ions using electrostatic fields. The best known is the Fusor. This device has a cathode inside an anode wire cage. Positive ions fly towards the negative inner cage, and are heated by the electric field in the process. If they miss the inner cage they can collide and fuse. Ions typically hit the cathode, however, creating prohibitory high conduction losses. Also, fusion rates in fusors are very low because of competing physical effects, such as energy loss in the form of light radiation.[68] Designs have been proposed to avoid the problems associated with the cage, by generating the field using a non-neutral cloud. These include a plasma oscillating device,[69] a magnetically-shielded-grid, a penning trap, the polywell[70] and the F1 cathode driver concept. The technology is relatively immature, however, and many scientific and engineering questions remain.

## History

### 1920s

Research into nuclear fusion started in the early part of the 20th century. In 1920 the British physicist Francis William Aston discovered that the total mass equivalent of four hydrogen atoms are heavier than the total mass of one helium atom (He-4), which implied that net energy can be released by combining hydrogen atoms together to form helium, and provided the first hints of a mechanism by which stars could produce energy in the quantities being measured. Through the 1920s, Arthur Stanley Eddington became a major proponent of the proton–proton chain reaction (PP reaction) as the primary system running the Sun.

### 1930s

Neutrons from fusion was first detected by staff members of Ernest Rutherfords' at the University of Cambridge, in 1933.[71] The experiment was developed by Mark Oliphant and involved the acceleration of protons towards a target [72] at energies of up to 600,000 electron volts. In 1933, the Cavendish Laboratory received a gift from the American physical chemist Gilbert N. Lewis of a few drops of heavy water. The accelerator was used to fire heavy hydrogen nuclei deuterons at various targets. Working with Rutherford and others, Oliphant discovered the nuclei of Helium-3 (helions) and tritium (tritons).[73][74][75][76]

A theory was verified by Hans Bethe in 1939 showing that beta decay and quantum tunneling in the Sun's core might convert one of the protons into a neutron and thereby producing deuterium rather than a diproton. The deuterium would then fuse through other reactions to further increase the energy output. For this work, Bethe won the Nobel Prize in Physics.

### 1940s

The first patent related to a fusion reactor was registered in 1946[77] by the United Kingdom Atomic Energy Authority. The inventors were Sir George Paget Thomson and Moses Blackman. This was the first detailed examination of the Z-pinch concept. Starting in 1947, two UK teams carried out small experiments based on this concept and began building a series of ever-larger experiments.

### 1950s

The first man-made device to achieve ignition was the detonation of this fusion device, codenamed Ivy Mike.
Early photo of plasma inside a pinch machine (Imperial College 1950/1951)

The first successful man-made fusion device was the boosted fission weapon tested in 1951 in the Greenhouse Item test. This was followed by true fusion weapons in 1952's Ivy Mike, and the first practical examples in 1954's Castle Bravo. This was uncontrolled fusion. In these devices, the energy released by the fission explosion is used to compress and heat fusion fuel, starting a fusion reaction. Fusion releases neutrons. These neutrons hit the surrounding fission fuel, causing the atoms to split apart much faster than normal fission processes—almost instantly by comparison. This increases the effectiveness of bombs: normal fission weapons blow themselves apart before all their fuel is used; fusion/fission weapons do not have this practical upper limit.

In 1949 an expatriate German, Ronald Richter, proposed the Huemul Project in Argentina, announcing positive results in 1951. These turned out to be fake, but it prompted considerable interest in the concept as a whole. In particular, it prompted Lyman Spitzer to begin considering ways to solve some of the more obvious problems involved in confining a hot plasma, and, unaware of the z-pinch efforts, he developed a new solution to the problem known as the stellarator. Spitzer applied to the US Atomic Energy Commission for funding to build a test device. During this period, James L. Tuck who had worked with the UK teams on z-pinch had been introducing the concept to his new coworkers at the Los Alamos National Laboratory (LANL). When he heard of Spitzer's pitch for funding, he applied to build a machine of his own, the Perhapsatron.

Spitzer's idea won funding and he began work on the stellarator under the code name Project Matterhorn. His work led to the creation of the Princeton Plasma Physics Laboratory. Tuck returned to LANL and arranged local funding to build his machine. By this time, however, it was clear that all of the pinch machines were suffering from the same issues involving instability, and progress stalled. In 1953, Tuck and others suggested a number of solutions to the stability problems. This led to the design of a second series of pinch machines, led by the UK ZETA and Sceptre devices.

Spitzer had planned an aggressive development project of four machines, A, B, C, and D. A and B were small research devices, C would be the prototype of a power-producing machine, and D would be the prototype of a commercial device. A worked without issue, but even by the time B was being used it was clear the stellarator was also suffering from instabilities and plasma leakage. Progress on C slowed as attempts were made to correct for these problems.

In 1954, Lewis Strauss, then chairman of the United States Atomic Energy Commission (U.S. AEC, forerunner of the U.S. Nuclear Regulatory Commission and the United States Department of Energy) spoke of electricity in the future being "too cheap to meter".[78] Strauss was very likely referring to hydrogen fusion[79] —which was secretly being developed as part of Project Sherwood at the time—but Strauss's statement was interpreted as a promise of very cheap energy from nuclear fission. The U.S. AEC itself had issued far more realistic testimony regarding nuclear fission to the U.S. Congress only months before, projecting that "costs can be brought down... [to]... about the same as the cost of electricity from conventional sources..."[80]

By the mid-1950s it was clear that the simple theoretical tools being used to calculate the performance of all fusion machines were simply not predicting their actual behavior. Machines invariably leaked their plasma from their confinement area at rates far higher than predicted. In 1954, Edward Teller held a gathering of fusion researchers at the Princeton Gun Club, near the Project Matterhorn (now known as Project Sherwood) grounds. Teller started by pointing out the problems that everyone was having, and suggested that any system where the plasma was confined within concave fields was doomed to fail. Attendees remember him saying something to the effect that the fields were like rubber bands, and they would attempt to snap back to a straight configuration whenever the power was increased, ejecting the plasma. He went on to say that it appeared the only way to confine the plasma in a stable configuration would be to use convex fields, a "cusp" configuration.[81]

When the meeting concluded, most of the researchers quickly turned out papers saying why Teller's concerns did not apply to their particular device. The pinch machines did not use magnetic fields in this way at all, while the mirror and stellarator seemed to have various ways out. This was soon followed by a paper by Martin David Kruskal and Martin Schwarzschild discussing pinch machines, however, which demonstrated instabilities in those devices were inherent to the design.

The largest "classic" pinch device was the ZETA, including all of these suggested upgrades, starting operations in the UK in 1957. In early 1958, John Cockcroft announced that fusion had been achieved in the ZETA, an announcement that made headlines around the world. When physicists in the US expressed concerns about the claims they were initially dismissed. US experiments soon demonstrated the same neutrons, although temperature measurements suggested these could not be from fusion reactions. The neutrons seen in the UK were later demonstrated to be from different versions of the same instability processes that plagued earlier machines. Cockcroft was forced to retract the fusion claims, and the entire field was tainted for years. ZETA ended its experiments in 1968.

The first experiment to achieve controlled thermonuclear fusion was accomplished using Scylla I at the Los Alamos National Laboratory in 1958.[27] Scylla I was a θ-pinch machine, with a cylinder full of deuterium. Electric current shot down the sides of the cylinder. The current made magnetic fields that pinched the plasma, raising temperatures to 15 million degrees Celsius, for long enough that atoms fused and produce neutrons.[26][27] The sherwood program sponsored a series of Scylla machines at Los Alamos. The program began with 5 researchers and 100,000 in US funding in January 1952.[82] By 1965, a total of 21 million had been spent on the program and staffing never reached above 65.

In 1950–1951 I.E. Tamm and A.D. Sakharov in the Soviet Union, first discussed a tokamak-like approach. Experimental research on those designs began in 1956 at the Kurchatov Institute in Moscow by a group of Soviet scientists led by Lev Artsimovich. The tokamak essentially combined a low-power pinch device with a low-power simple stellarator. The key was to combine the fields in such a way that the particles orbited within the reactor a particular number of times, today known as the "safety factor". The combination of these fields dramatically improved confinement times and densities, resulting in huge improvements over existing devices.

### 1960s

A key plasma physics text was published by Lyman Spitzer at Princeton in 1963.[83] Spitzer took the ideal gas laws and adapted them to an ionized plasma, developing many of the fundamental equations used to model a plasma.

Laser fusion was suggested in 1962 by scientists at Lawrence Livermore National Laboratory, shortly after the invention of the laser itself in 1960. At the time, Lasers were low power machines, but low-level research began as early as 1965. Laser fusion, formally known as inertial confinement fusion, involves imploding a target by using laser beams. There are two ways to do this: indirect drive and direct drive. In direct drive, the laser blasts a pellet of fuel. In indirect drive, the lasers blast a structure around the fuel. This makes x-rays that squeeze the fuel. Both methods compress the fuel so that fusion can take place.

At the 1964 World's Fair, the public was given its first demonstration of nuclear fusion.[84] The device was a θ-pinch from General Electric. This was similar to the Scylla machine developed earlier at Los Alamos.

The magnetic mirror was first published in 1967 by Richard F. Post and many others at the Lawrence Livermore National Laboratory.[17] The mirror consisted of two large magnets arranged so they had strong fields within them, and a weaker, but connected, field between them. Plasma introduced in the area between the two magnets would "bounce back" from the stronger fields in the middle.

The A.D. Sakharov group constructed the first tokamaks, the most successful being the T-3 and its larger version T-4. T-4 was tested in 1968 in Novosibirsk, producing the world's first quasistationary fusion reaction.[85] When this was first announced, the international community was highly skeptical. A British team was invited to see T-3, however, and after measuring it in depth they released their results that confirmed the Soviet claims. A burst of activity followed as many planned devices were abandoned and new tokamaks were introduced in their place — the C model stellarator, then under construction after many redesigns, was quickly converted to the Symmetrical Tokamak.

In his work with vacuum tubes, Philo Farnsworth observed that electric charge would accumulate in regions of the tube. Today, this effect is known as the Multipactor effect.[86] Farnsworth reasoned that if ions were concentrated high enough they could collide and fuse. In 1962, he filed a patent on a design using a positive inner cage to concentrate plasma, in order to achieve nuclear fusion.[87] During this time, Robert L. Hirsch joined the Farnsworth Television labs and began work on what became the fusor. Hirsch patented the design in 1966[88] and published the design in 1967.[89]

### 1970s

Shiva laser, 1977, the largest ICF laser system built in the seventies
The Tandem Mirror Experiment (TMX) in 1979

In 1972, John Nuckolls outlined the idea of ignition.[22] This is a fusion chain reaction. Hot helium made during fusion reheats the fuel and starts more reactions. John argued that ignition would require lasers of about 1 kJ. This turned out to be wrong. Nuckolls's paper started a major development effort. Several laser systems were built at LLNL. These included the argus, the Cyclops, the Janus, the long path, the Shiva laser and the Nova in 1984. This prompted the UK to build the Central Laser Facility in 1976.[90]

During this time, great strides in understanding the tokamak system were made. A number of improvements to the design are now part of the "advanced tokamak" concept, which includes non-circular plasma, internal diverters and limiters, often superconducting magnets, and operate in the so-called "H-mode" island of increased stability. Two other designs have also become fairly well studied; the compact tokamak is wired with the magnets on the inside of the vacuum chamber, while the spherical tokamak reduces its cross section as much as possible.

In 1974 a study of the ZETA results demonstrated an interesting side-effect; after an experimental run ended, the plasma would enter a short period of stability. This led to the reversed field pinch concept, which has seen some level of development since. On May 1, 1974, the KMS fusion company (founded by Kip Siegel) achieves the world's first laser induced fusion in a deuterium-tritium pellet.[91]

In the mid-1970s, Project PACER, carried out at Los Alamos National Laboratory (LANL) explored the possibility of a fusion power system that would involve exploding small hydrogen bombs (fusion bombs) inside an underground cavity.[92] As an energy source, the system is the only fusion power system that could be demonstrated to work using existing technology. It would also require a large, continuous supply of nuclear bombs, however, making the economics of such a system rather questionable.

In 2019 the United Kingdom announced a planned £200-million (US$248-million) investment to produce a design for a fusion facility named the Spherical Tokamak for Energy Production (STEP), by the early 2040s.[184][185] ## Fuels By firing particle beams at targets, many fusion reactions have been tested, while the fuels considered for power have all been light elements like the isotopes of hydrogen—protium, deuterium, and tritium.[3] The deuterium and helium-3 reaction requires helium-3, an isotope of helium so scarce on Earth that it would have to be mined extraterrestrially or produced by other nuclear reactions. Finally, researchers hope to perform the protium and boron-11 reaction, because it does not directly produce neutrons, though side reactions can.[186] ### Deuterium, tritium Diagram of the D-T reaction The easiest nuclear reaction, at the lowest energy, is: 2 1 D + 3 1 T 4 2 He (3.5 MeV) + 1 0 n (14.1 MeV) This reaction is common in research, industrial and military applications, usually as a convenient source of neutrons. Deuterium is a naturally occurring isotope of hydrogen and is commonly available. The large mass ratio of the hydrogen isotopes makes their separation easy compared to the difficult uranium enrichment process. Tritium is a natural isotope of hydrogen, but because it has a short half-life of 12.32 years, it is hard to find, store, produce, and is expensive. Consequently, the deuterium-tritium fuel cycle requires the breeding of tritium from lithium using one of the following reactions: 1 0 n + 6 3 Li 3 1 T + 4 2 He 1 0 n + 7 3 Li 3 1 T + 4 2 He + 1 0 n The reactant neutron is supplied by the D-T fusion reaction shown above, and the one that has the greatest yield of energy. The reaction with 6Li is exothermic, providing a small energy gain for the reactor. The reaction with 7Li is endothermic but does not consume the neutron. At least some neutron multiplication reactions are required to replace the neutrons lost to absorption by other elements. Leading candidate neutron multiplication materials are beryllium and lead however the 7Li reaction above also helps to keep the neutron population high. Natural lithium is mainly 7Li however this has a low tritium production cross section compared to 6Li so most reactor designs use breeder blankets with enriched 6Li. Several drawbacks are commonly attributed to D-T fusion power: 1. It produces substantial amounts of neutrons that result in the neutron activation of the reactor materials.[187] 2. Only about 20% of the fusion energy yield appears in the form of charged particles with the remainder carried off by neutrons, which limits the extent to which direct energy conversion techniques might be applied.[188] 3. It requires the handling of the radioisotope tritium. Similar to hydrogen, tritium is difficult to contain and may leak from reactors in some quantity. Some estimates suggest that this would represent a fairly large environmental release of radioactivity.[189] The neutron flux expected in a commercial D-T fusion reactor is about 100 times that of current fission power reactors, posing problems for material design. After a series of D-T tests at JET, the vacuum vessel was sufficiently radioactive that remote handling was required for the year following the tests.[190] In a production setting, the neutrons would be used to react with lithium in the context of a breeder blanket comprising lithium ceramic pebbles or liquid lithium, in order to create more tritium. This also deposits the energy of the neutrons in the lithium, which would then be transferred to drive electrical production. The lithium neutron absorption reaction protects the outer portions of the reactor from the neutron flux. Newer designs, the advanced tokamak in particular, also use lithium inside the reactor core as a key element of the design. The plasma interacts directly with the lithium, preventing a problem known as "recycling". The advantage of this design was demonstrated in the Lithium Tokamak Experiment. ### Deuterium Deuterium fusion cross section (in square meters) at different ion collision energies. This is the second easiest fusion reaction, fusing two deuterium nuclei. The reaction has two branches that occur with nearly equal probability:  D + D → T + 1H D + D → 3He + n This reaction is also common in research. The optimum energy to initiate this reaction is 15 keV, only slightly higher than the optimum for the D-T reaction. The first branch does not produce neutrons, but it does produce tritium, so that a D-D reactor will not be completely tritium-free, even though it does not require an input of tritium or lithium. Unless the tritons can be quickly removed, most of the tritium produced would be burned before leaving the reactor, which would reduce the handling of tritium, but would produce more neutrons, some of which are very energetic. The neutron from the second branch has an energy of only 2.45 MeV (0.393 pJ), whereas the neutron from the D-T reaction has an energy of 14.1 MeV (2.26 pJ), resulting in a wider range of isotope production and material damage. When the tritons are removed quickly while allowing the 3He to react, the fuel cycle is called "tritium suppressed fusion"[191] The removed tritium decays to 3He with a 12.5 year half life. By recycling the 3He produced from the decay of tritium back into the fusion reactor, the fusion reactor does not require materials resistant to fast 14.1 MeV (2.26 pJ) neutrons. Assuming complete tritium burn-up, the reduction in the fraction of fusion energy carried by neutrons would be only about 18%, so that the primary advantage of the D-D fuel cycle is that tritium breeding would not be required. Other advantages are independence from scarce[dubious ] lithium resources and a somewhat softer neutron spectrum. The disadvantage of D-D compared to D-T is that the energy confinement time (at a given pressure) must be 30 times longer and the power produced (at a given pressure and volume) would be 68 times less.[citation needed] Assuming complete removal of tritium and recycling of 3He, only 6% of the fusion energy is carried by neutrons. The tritium-suppressed D-D fusion requires an energy confinement that is 10 times longer compared to D-T and a plasma temperature that is twice as high.[192] ### Deuterium, helium-3 A second-generation approach to controlled fusion power involves combining helium-3 (3He) and deuterium (2H):  D + 3He → 4He + 1H This reaction produces a helium-4 nucleus (4He) and a high-energy proton. As with the p-11B aneutronic fusion fuel cycle, most of the reaction energy is released as charged particles, reducing activation of the reactor housing and potentially allowing more efficient energy harvesting (via any of several speculative technologies).[citation needed] In practice, D-D side reactions produce a significant number of neutrons, resulting in p-11B being the preferred cycle for aneutronic fusion.[citation needed] ### Proton, boron-11 Both material science problems and non proliferation concerns are greatly diminished if aneutronic fusion can be achieved. Theoretically, the most reactive a-neutronic fusion fuel is 3He. However, obtaining reasonable quantities of 3He would require large scale mining operations on the moon or in the atmosphere of Uranus or Saturn, which raise other, quite considerable technical difficulties. Therefore the most promising candidate fuel for such fusion is fusing the readily available hydrogen-1 (i.e. a proton) and boron. Their fusion releases no neutrons, but produces energetic charged alpha (helium) particles whose energy can directly be converted to electric power p + 11B → 3 4He Under reasonable assumptions, side reactions will result in only about 0.1% of the fusion power being carried by neutrons,[193] which means that neutron scattering is not used for energy transfer and material activation is reduced several thousand times. Unfortunately, the optimum temperature for this reaction of 123 keV[clarification needed] is nearly ten times higher than that for pure hydrogen reactions, and the energy confinement must be 500 times better than that required for the D-T reaction. In addition the power density is 2500 times lower than for D-T, although per unit mass of fuel, this is still considerably higher than for fission reactors. Because the confinement properties of conventional approaches to fusion such as the tokamak and laser pellet fusion are marginal, most proposals for aneutronic fusion are based on radically different confinement concepts, such as the Polywell and the Dense Plasma Focus. In 2013 a research team led by Christine Labaune at École Polytechnique in Palaiseau, France, reported a new fusion rate record for proton-boron fusion, with an estimated 80 million fusion reactions during 1.5 nanoseconds laser fire, over 100 times more than previous proton-boron experiments.[194][195] ## Material selection ### Considerations Even on smaller plasma production scales, the material of the containment apparatus will be intensely blasted with matter and energy. Designs for plasma containment must consider: Depending on the approach, these effects may be higher or lower than typical fission reactors like the pressurized water reactor (PWR).[196] One estimate put the radiation at 100 times that of a typical PWR.[citation needed] Materials need to be selected or developed that can withstand these basic conditions.[197][198] Depending on the approach, however, there may be other considerations such as electrical conductivity, magnetic permeability and mechanical strength. There is also a need for materials whose primary components and impurities do not result in long-lived radioactive wastes. ### Durability For long term use, each atom in the wall is expected to be hit by a neutron and displaced about a hundred times before the material is replaced. High-energy neutrons will produce hydrogen and helium by way of various nuclear reactions that tends to form bubbles at grain boundaries and result in swelling, blistering or embrittlement.[196] ### Selection One can choose either a low-Z material, such as graphite or beryllium, or a high-Z material, usually tungsten with molybdenum as a second choice. Use of liquid metals (lithium, gallium, tin) has also been proposed, e.g., by injection of 1–5 mm thick streams flowing at 10 m/s on solid substrates.[citation needed] If graphite is used, the gross erosion rates due to physical and chemical sputtering would be many meters per year, so one must rely on redeposition of the sputtered material. The location of the redeposition will not exactly coincide with the location of the sputtering, so one is still left with erosion rates that may be prohibitive. An even larger problem is the tritium co-deposited with the redeposited graphite. The tritium inventory in graphite layers and dust in a reactor could quickly build up to many kilograms, representing a waste of resources and a serious radiological hazard in case of an accident. The consensus of the fusion community seems to be that graphite, although a very attractive material for fusion experiments, cannot be the primary plasma-facing material (PFM) in a commercial reactor. The sputtering rate of tungsten by the plasma fuel ions is orders of magnitude smaller than that of carbon, and tritium is much less incorporated into redeposited tungsten, making this a more attractive choice. On the other hand, tungsten impurities in a plasma are much more damaging than carbon impurities, and self-sputtering of tungsten can be high, so it will be necessary to ensure that the plasma in contact with the tungsten is not too hot (a few tens of eV rather than hundreds of eV). Tungsten also has disadvantages in terms of eddy currents and melting in off-normal events, as well as some radiological issues. ## Safety and the environment ### Accident potential Unlike nuclear fission, fusion requires extremely precise and controlled temperature, pressure and magnetic field parameters for any net energy to be produced. If a reactor suffers damage or loses even a small degree of required control, fusion reactions and heat generation would rapidly cease.[199] Additionally, fusion reactors contain only small amounts of fuel, enough to "burn" for minutes, or in some cases, microseconds. Unless they are actively refueled, the reactions will quickly end. Therefore, fusion reactors are considered immune from catastrophic meltdown.[200] For similar reasons, runaway reactions cannot occur in a fusion reactor. The plasma is burnt at optimal conditions, and any significant change will simply quench the reactions. The reaction process is so delicate that this level of safety is inherent. Although the plasma in a fusion power station is expected to have a volume of 1,000 cubic metres (35,000 cu ft) or more, the plasma density is low and typically contains only a few grams of fuel in use.[200] If the fuel supply is closed, the reaction stops within seconds. In comparison, a fission reactor is typically loaded with enough fuel for several months or years, and no additional fuel is necessary to continue the reaction. It is this large amount of fuel that gives rise to the possibility of a meltdown; nothing like this exists in a fusion reactor.[201] In the magnetic approach, strong fields are developed in coils that are held in place mechanically by the reactor structure. Failure of this structure could release this tension and allow the magnet to "explode" outward. The severity of this event would be similar to any other industrial accident or an MRI machine quench/explosion, and could be effectively stopped with a containment building similar to those used in existing (fission) nuclear generators. The laser-driven inertial approach is generally lower-stress because of the increased size of the reaction chamber. Although failure of the reaction chamber is possible, simply stopping fuel delivery would prevent any sort of catastrophic failure.[citation needed] Most reactor designs rely on liquid hydrogen as both a coolant and a method for converting stray neutrons from the reaction into tritium, which is fed back into the reactor as fuel. Hydrogen is highly flammable, and in the case of a fire it is possible that the hydrogen stored on-site could be burned up and escape. In this case, the tritium contents of the hydrogen would be released into the atmosphere, posing a radiation risk. Calculations suggest that at about 1 kilogram (2.2 lb), the total amount of tritium and other radioactive gases in a typical power station would be so small that they would have diluted to legally acceptable limits by the time they blew as far as the station's perimeter fence.[202] The likelihood of small industrial accidents, including the local release of radioactivity and injury to staff, cannot be estimated yet. These would include accidental releases of lithium or tritium or mishandling of decommissioned radioactive components of the reactor itself.[citation needed] ### Magnet quench A quench is an abnormal termination of magnet operation that occurs when part of the superconducting coil enters the normal (resistive) state. This can occur because the field inside the magnet is too large, the rate of change of field is too large (causing eddy currents and resultant heating in the copper support matrix), or a combination of the two. More rarely a defect in the magnet can cause a quench. When this happens, that particular spot is subject to rapid Joule heating from the enormous current, which raises the temperature of the surrounding regions. This pushes those regions into the normal state as well, which leads to more heating in a chain reaction. The entire magnet rapidly becomes normal (this can take several seconds, depending on the size of the superconducting coil). This is accompanied by a loud bang as the energy in the magnetic field is converted to heat, and rapid boil-off of the cryogenic fluid. The abrupt decrease of current can result in kilovolt inductive voltage spikes and arcing. Permanent damage to the magnet is rare, but components can be damaged by localized heating, high voltages, or large mechanical forces. In practice, magnets usually have safety devices to stop or limit the current when the beginning of a quench is detected. If a large magnet undergoes a quench, the inert vapor formed by the evaporating cryogenic fluid can present a significant asphyxiation hazard to operators by displacing breathable air. A large section of the superconducting magnets in CERN's Large Hadron Collider unexpectedly quenched during start-up operations in 2008, necessitating the replacement of a number of magnets.[203] In order to mitigate against potentially destructive quenches, the superconducting magnets that form the LHC are equipped with fast-ramping heaters which are activated once a quench event is detected by the complex quench protection system. As the dipole bending magnets are connected in series, each power circuit includes 154 individual magnets, and should a quench event occur, the entire combined stored energy of these magnets must be dumped at once. This energy is transferred into dumps that are massive blocks of metal which heat up to several hundreds of degrees Celsius—because of resistive heating—in a matter of seconds. Although undesirable, a magnet quench is a "fairly routine event" during the operation of a particle accelerator.[204] ### Effluents The natural product of the fusion reaction is a small amount of helium, which is completely harmless to life. Of more concern is tritium, which, like other isotopes of hydrogen, is difficult to retain completely. During normal operation, some amount of tritium will be continually released.[citation needed] Although tritium is volatile and biologically active, the health risk posed by a release is much lower than that of most radioactive contaminants, because of tritium's short half-life (12.32 years) and very low decay energy (~14.95 keV), and because it does not bioaccumulate (instead being cycled out of the body as water, with a biological half-life of 7 to 14 days).[205] Current ITER designs are investigating total containment facilities for any tritium. ### Waste management The large flux of high-energy neutrons in a reactor will make the structural materials radioactive. The radioactive inventory at shut-down may be comparable to that of a fission reactor, but there are important differences. The half-life of the radioisotopes produced by fusion tends to be less than those from fission, so that the inventory decreases more rapidly. Unlike fission reactors, whose waste remains radioactive for thousands of years, most of the radioactive material in a fusion reactor would be the reactor core itself, which would be dangerous for about 50 years, and low-level waste for another 100.[206] Although this waste will be considerably more radioactive during those 50 years than fission waste, the very short half-life makes the process very attractive, as the waste management is fairly straightforward. By 500 years the material would have the same radiotoxicity as coal ash.[202] Additionally, the choice of materials used in a fusion reactor is less constrained than in a fission design, where many materials are required for their specific neutron cross-sections. This allows a fusion reactor to be designed using materials that are selected specifically to be "low activation", materials that do not easily become radioactive. Vanadium, for example, would become much less radioactive than stainless steel. Carbon fiber materials are also low-activation, as well as being strong and light, and are a promising area of study for laser-inertial reactors where a magnetic field is not required. In general terms, fusion reactors would create far less radioactive material than a fission reactor, the material it would create is less damaging biologically, and the radioactivity "burns off" within a time period that is well within existing engineering capabilities for safe long-term waste storage. ### Nuclear proliferation Although fusion power uses nuclear technology, the overlap with nuclear weapons would be limited. A huge amount of tritium could be produced by a fusion power station; tritium is used in the trigger of hydrogen bombs and in a modern boosted fission weapon, but it can also be produced by nuclear fission. The energetic neutrons from a fusion reactor could be used to breed weapons-grade plutonium or uranium for an atomic bomb (for example by transmutation of U238 to Pu239, or Th232 to U233). A study conducted 2011 assessed the risk of three scenarios:[207] • Use in small-scale fusion station: As a result of much higher power consumption, heat dissipation and a more recognizable design compared to enrichment gas centrifuges this choice would be much easier to detect and therefore implausible.[207] • Modifications to produce weapon-usable material in a commercial facility: The production potential is significant. But no fertile or fissile substances necessary for the production of weapon-usable materials needs to be present at a civil fusion system at all. If not shielded, a detection of these materials can be done by their characteristic gamma radiation. The underlying redesign could be detected by regular design information verifications. In the (technically more feasible) case of solid breeder blanket modules, it would be necessary for incoming components to be inspected for the presence of fertile material,[207] otherwise plutonium for several weapons could be produced each year.[208] • Prioritizing a fast production of weapon-grade material regardless of secrecy: The fastest way to produce weapon usable material was seen in modifying a prior civil fusion power station. Unlike in some nuclear power stations, there is no weapon compatible material during civil use. Even without the need for covert action this modification would still take about 2 months to start the production and at least an additional week to generate a significant amount for weapon production. This was seen as enough time to detect a military use and to react with diplomatic or military means. To stop the production, a military destruction of inevitable parts of the facility leaving out the reactor itself would be sufficient. This, together with the intrinsic safety of fusion power would only bear a low risk of radioactive contamination.[207] Another study concludes that "[..]large fusion reactors – even if not designed for fissile material breeding – could easily produce several hundred kg Pu per year with high weapon quality and very low source material requirements." It was emphasized that the implementation of features for intrinsic proliferation resistance might only be possible at this phase of research and development.[208] The theoretical and computational tools needed for hydrogen bomb design are closely related to those needed for inertial confinement fusion, but have very little in common with the more scientifically developed magnetic confinement fusion. ### Energy source Large-scale reactors using neutronic fuels (e.g. ITER) and thermal power production (turbine based) are most comparable to fission power from an engineering and economics viewpoint. Both fission and fusion power stations involve a relatively compact heat source powering a conventional steam turbine-based power station, while producing enough neutron radiation to make activation of the station materials problematic. The main distinction is that fusion power produces no high-level radioactive waste (though activated station materials still need to be disposed of). There are some power station ideas that may significantly lower the cost or size of such stations; however, research in these areas is nowhere near as advanced as in tokamaks.[citation needed] Fusion power commonly proposes the use of deuterium, an isotope of hydrogen, as fuel and in many current designs also use lithium. Assuming a fusion energy output equal to the 1995 global power output of about 100 EJ/yr (= 1 × 1020 J/yr) and that this does not increase in the future, which is unlikely, then the known current lithium reserves would last 3000 years. Lithium from sea water would last 60 million years, however, and a more complicated fusion process using only deuterium would have fuel for 150 billion years.[209] To put this in context, 150 billion years is close to 30 times the remaining lifespan of the sun,[210] and more than 10 times the estimated age of the universe. ## Economics While fusion power is still in early stages of development, substantial sums have been and continue to be invested in research. In the EU almost €10 billion was spent on fusion research up to the end of the 1990s, and the new ITER reactor alone is budgeted at €6.6 billion total for the timeframe between 2008 and 2020.[211] It is estimated that up to the point of possible implementation of electricity generation by nuclear fusion, R&D will need further promotion totalling around €60–80 billion over a period of 50 years or so (of which €20–30 billion within the EU) based on a report from 2002.[212] Nuclear fusion research receives €750 million (excluding ITER funding) from the European Union, compared with €810 million for sustainable energy research,[213] putting research into fusion power well ahead of that of any single rivaling technology. Indeed, the size of the investments and time frame of the expected results mean that fusion research is almost exclusively publicly funded, while research in other forms of energy can be done by the private sector. In spite of that, a number of start-up companies active in the field of fusion power have managed to attract private money.[214] ## Advantages Fusion power would provide more energy for a given weight of fuel than any fuel-consuming energy source currently in use,[215] and the fuel itself (primarily deuterium) exists abundantly in the Earth's ocean: about 1 in 6500 hydrogen atoms in seawater is deuterium.[216] Although this may seem a low proportion (about 0.015%), because nuclear fusion reactions are so much more energetic than chemical combustion and seawater is easier to access and more plentiful than fossil fuels, fusion could potentially supply the world's energy needs for millions of years.[217][218] A scenario has been presented of the effect of the commercialization of fusion power on the future of human civilization.[219] ITER and later DEMO are envisioned to bring online the first commercial nuclear fusion energy reactor by 2050. Using this as the starting point and the history of the uptake of nuclear fission reactors as a guide, the scenario depicts a rapid take up of nuclear fusion energy starting after the middle of this century.[citation needed] Fusion power could be used in interstellar space where solar energy is not available.[220] ## See also ## References 1. ^ "Nuclear Fusion : WNA". world-nuclear.org. November 2015. Archived from the original on 2015-07-19. Retrieved 2015-07-26. 2. ^ "Fission and fusion can yield energy". Hyperphysics.phy-astr.gsu.edu. Retrieved 30 October 2014. 3. ^ a b c Miley, G.H.; Towner, H.; Ivich, N. (1974-06-17). "SciTech Connect: Fusion cross sections and reactivities". Osti.gov. doi:10.2172/4014032. OSTI 4014032. Cite journal requires |journal= (help) 4. Lawson, J D (1 December 1956). "Some Criteria for a Power Producing Thermonuclear Reactor". Proceedings of the Physical Society. Section B. IOP Publishing. 70 (1): 6–10. doi:10.1088/0370-1301/70/1/303. ISSN 0370-1301. 5. ^ "Lawson's three criteria". EFDA. February 25, 2013. Archived from the original on 2014-09-11. Retrieved 2014-08-24. 6. ^ "Triple product". EFDA. 2014-06-20. Archived from the original on 2014-09-11. Retrieved 2014-08-24. 7. ^ "Laser Inertial Fusion Energy". Life.llnl.gov. Archived from the original on 2014-09-15. Retrieved 2014-08-24. 8. ^ a b Barr, W. L.; Moir, R. W.; Hamilton, G. W. (1982). "Experimental results from a beam direct converter at 100 kV". Journal of Fusion Energy. Springer Science and Business Media LLC. 2 (2): 131–143. doi:10.1007/bf01054580. ISSN 0164-0313. 9. ^ Fitzpatrick, Richard. "Magnetized plasma". Introduction to Plasma Physics. 10. ^ Alfvén, H (1942). "Existence of electromagnetic-hydrodynamic waves". Nature. 150 (3805): 405–406. Bibcode:1942Natur.150..405A. doi:10.1038/150405d0. 11. ^ Tuszewski, M. (1988). "Field reversed configurations". Nuclear Fusion (Submitted manuscript). 28 (11): 2033–2092. doi:10.1088/0029-5515/28/11/008. 12. ^ Engelhardt, W. (2005-01-01). "Is a Plasma Diamagnetic?". Physics Essays. 18 (4): 504–513. arXiv:physics/0510139. Bibcode:2005PhyEs..18..504E. doi:10.4006/1.3025762. 13. ^ R. F. Post, Proc. of Second U.N. Int. Conf. on Peaceful Uses of Atomic Energy, Vol. 32, p. 245 (Geneva, 1958) 14. ^ "All-the-Worlds-Tokamaks". tokamak.info. 15. ^ 16. ^ "MIT tests unique approach to fusion power". MIT News, David Chandler, MIT News Office, March 19, 2008. Accessed March 2008 17. ^ a b "Mirror Systems: Fuel Cycles, loss reduction and energy recovery" by Richard F. Post, BNES Nuclear fusion reactor conferences at Culham laboratory, September 1969. 18. ^ J Berowitz, H Grad and H Rubin, in proceedings of the second United Nations International conference on peaceful uses of atomic energy, Geneva, 1958, Vol 31, Page 177 19. ^ Bagryansky, P. A.; Shalashov, A. G.; Gospodchikov, E. D.; Lizunov, A. A.; Maximov, V. V.; Prikhodko, V. V.; Soldatkina, E. I.; Solomakhin, A. L.; Yakovlev, D. V. (18 May 2015). "Threefold Increase of the Bulk Electron Temperature of Plasma Discharges in a Magnetic Mirror Device". Physical Review Letters. American Physical Society (APS). 114 (20): 205001. arXiv:1411.6288. doi:10.1103/physrevlett.114.205001. ISSN 0031-9007. PMID 26047233. 20. ^ Freidberg, Jeffrey P. (8 February 2007). Plasma Physics and Fusion Energy. Cambridge University Press. ISBN 978-0-521-85107-7. 21. ^ Dolan, Thomas J., ed. (2013). Magnetic Fusion Technology. Lecture Notes in Energy. 19. London: Springer London. pp. 30–40. doi:10.1007/978-1-4471-5556-0. ISBN 978-1-4471-5555-3. ISSN 2195-1284. 22. ^ a b Nuckolls, John; Wood, Lowell; Thiessen, Albert; Zimmerman, George (1972). "Laser Compression of Matter to Super-High Densities: Thermonuclear (CTR) Applications". Nature. 239 (5368): 139–142. Bibcode:1972Natur.239..139N. doi:10.1038/239139a0. 23. ^ 24. ^ Thio, Y C F (1 April 2008). "Status of the US program in magneto-inertial fusion". Journal of Physics: Conference Series. IOP Publishing. 112 (4): 042084. doi:10.1088/1742-6596/112/4/042084. ISSN 1742-6596. 25. ^ Sharp, W. M.; et al. (2011). Inertial Fusion Driven by Intense Heavy-Ion Beams (PDF). Proceedings of 2011 Particle Accelerator Conference. New York, NY, USA. p. 1386. 26. ^ a b Seife, Charles (2008). Sun in a bottle : the strange history of fusion and the science of wishful thinking. New York: Viking. ISBN 978-0-670-02033-1. OCLC 213765956. 27. ^ a b c Phillips, James (1983). "Magnetic Fusion". Los Alamos Science: 64–67. Retrieved 4 Apr 2013. 28. ^ Srivastava, Krishna M.; Vyas, D. N. (1982). "Non-linear analysis of the stability of the Screw Pinch". Astrophysics and Space Science. Springer Nature. 86 (1): 71–89. doi:10.1007/bf00651831. ISSN 0004-640X. 29. ^ Rider, Todd H. (1995). "A general critique of inertial‐electrostatic confinement fusion systems". Physics of Plasmas. AIP Publishing. 2 (6): 1853–1872. doi:10.1063/1.871273. hdl:1721.1/29869. ISSN 1070-664X. 30. ^ Clynes, Tom (14 February 2012). "The Boy Who Played With Fusion". Popular Science. Retrieved 3 August 2019. 31. ^ US patent 5,160,695, Robert W. Bussard, "Method and apparatus for creating and controlling nuclear fusion reactions", issued 1992-11-03 32. ^ FRX-L: A Plasma Injector for Magnetized Target Fusion 33. ^ "Spherically imploding plasma liners as a standoff driver for MIF" IEEE transactions, 2012, Hsu, et al. 34. ^ Chang, Kenneth (7 March 2015). "Practical Fusion, or Just a Bubble?". The New York Times. Retrieved 3 August 2019. "Dr. Putterman's approach is to use sound waves, called sonofusion or bubble fusion, to expand and collapse tiny bubbles, generating ultrahot temperatures. At temperatures hot enough, atoms can literally fuse and release even more energy than when they split in nuclear fission, now used in nuclear power stations and weapons. Furthermore, fusion is clean[,] in that it does not produce long-lived nuclear waste." 35. ^ Chang, Kenneth (25 March 2004). "U.S. Will Give Cold Fusion Second Look, After 15 Years". The New York Times. Retrieved 3 August 2019. 36. ^ Ouellette, Jennifer (2011-12-23), Could Starships Use Cold Fusion Propulsion?, Discovery News. 37. ^ Nagamine, Kanetada. "Introductory Muon Science". Cambridge University Press, 2003, Chapter 5. 38. ^ 39. ^ Miley, George H., and S. Krupakar Murali. Inertial electrostatic confinement (IEC) fusion. New York: Springer, 2014. 40. ^ "NEUTRAL-BEAM INJECTION" W. B. Kunkel, Lawrence Livermore National Labs, FUSION, 1980 41. ^ McGuire, Thomas. Heating Plasma for Fusion Power Using Magnetic Field Oscillations. Baker Botts LLP, assignee. Issued: 4/2/14, Patent 14/243,447. N.d. Print. 42. ^ Esarey, Eric; Ride, Sally K.; Sprangle, Phillip (1 September 1993). "Nonlinear Thomson scattering of intense laser pulses from beams and plasmas". Physical Review E. American Physical Society (APS). 48 (4): 3003–3021. doi:10.1103/physreve.48.3003. ISSN 1063-651X. PMID 9960936. 43. ^ "Thomson scattering system on the TEXTOR tokamak using a multi-pass laser beam configuration" M Yu Kantor, A J H Donné, R Jaspers, Plasma Physics and Controlled Fusion, Volume 51, 5 44. ^ Mott-Smith, H. M.; Langmuir, Irving (1 September 1926). "The Theory of Collectors in Gaseous Discharges". Physical Review. American Physical Society (APS). 28 (4): 727–763. doi:10.1103/physrev.28.727. ISSN 0031-899X. 45. ^ "NCSX Vacuum Vessel External Flux Loops Design and Installation, PPPL, Twenty-Second Symposium on Fusion Engineering, 2007 46. ^ Park, Jaeyoung; Krall, Nicholas A.; Sieck, Paul E.; Offermann, Dustin T.; Skillicorn, Michael; Sanchez, Andrew; Davis, Kevin; Alderson, Eric; Lapenta, Giovanni (2014-06-01). "High Energy Electron Confinement in a Magnetic Cusp Configuration". Physical Review X. 5 (2): 021024. arXiv:1406.0133. Bibcode:2015PhRvX...5b1024P. doi:10.1103/PhysRevX.5.021024. 47. ^ J. Larmor, "On a dynamical theory of the electric and luminiferous medium", Philosophical Transactions of the Royal Society 190, (1897) pp. 205–300 (Third and last in a series of papers with the same name). 48. ^ "Study of steam, helium and supercritical CO2 turbine power generations in prototype fusion power reactor", S Ishiyama, Y Muto, Y Kato, S Nishio, Progress in Nuclear Fusion, 2008 49. ^ Seaver, Lynda L (8 November 2010). "Press release: World's largest laser sets records for neutron yield and laser energy". Lawrence Livermore National Laboratory. 50. ^ T. Anklam; A. J. Simon; S. Powers; W. R. Meier (December 2, 2010). "LIFE: The Case for Early Commercialization of Fusion Energy" (PDF). Livermore, LLNL-JRNL-463536. Archived from the original (PDF) on 4 September 2015. Retrieved 30 October 2014. 51. ^ Hanaor, D.A.H.; Kolb, M.H.H.; Gan, Y.; Kamlah, M.; Knitter, R. (2014). "Solution based synthesis of mixed-phase materials in the Li2TiO3-Li4SiO4 system". Journal of Nuclear Materials. 456: 151–161. arXiv:1410.7128. Bibcode:2015JNuM..456..151H. doi:10.1016/j.jnucmat.2014.09.028. 52. ^ "Mirror Systems: Fuel Cycles, loss reduction and energy recovery" by Richard F. Post, BNES Nuclear fusion reactor conferences at Culham laboratory, September 1969 53. ^ "Test results on plasma direct converters" William L. Barr and Ralph W Moir, Nuclear Technology Vol 3, January 1983 54. ^ "JET". Culham Centre Fusion Energy. Retrieved 26 June 2016. 55. ^ Cohen, Sam, and B. Berlinger. "Long-pulse Operation of the PFRC-2 Device." The Joint US-Japan Compact Torus. Wisconsin, Madison. 22 Aug. 2016. Lecture. 56. ^ "Fusion energy and why it is important to chase the impossible" Dr. Melanie Windridge, TED x Warwick, April 19th 2018. 57. ^ Wesson, J: "Tokamaks", 3rd edition page 115, Oxford University Press, 2004 58. ^ "Improved Confinement During Magnetic Levitation in LDX", 50th Annual Meeting of the APS DDP, November 18, 2008 M Manuel 59. ^ Ono, Y (1999). "New relaxation of merging spheromaks to a field reversed configuration". Nuclear Fusion 39 (11Y): 2001–2008. doi:10.1088/0029-5515/39/11Y/346. edit 60. ^ "Advanced Spheromak Fusion Reactor" T Fowler, E Hooper, 8th international conference on emerging nuclear energy ystems 61. ^ "Three Game Changing Discoveries: A Simpler Fusion Concept?" by Thomas C Simonen, Journal of Fusion Energy, 2016 62. ^ Gas Dynamic Trap (GDT). Experiments with Electron Heating. Budker Institute of Nuclear Physics, Novosibirsk State University. Siberian Branch, Russia, 2012, Thomas Simonen 63. ^ Wood R D, Hill D N, McLean H S, Hooper E B, Hudson B F, Moller J M, Romero-Talamas C A (2009) “Improved magnetic field generation efficiency and higher temperature spheromak plasmas,” Nuclear Fusion 49, 025001 (4pp). 64. ^ Booth, William. "Fusion's$372-Million Mothball." Science [New York City] 9 Oct. 1987, Volume 238 ed.: 152-55. Print
65. ^ Containment in a cusped Plasma System, Dr. Harold Grad, NYO-9496
66. ^ Pfalzner 2006, p. 19–20.
67. ^ Pfalzner 2006, p. 182–193.
68. ^ Thorson, Timothy A. (1996). Ion flow and fusion reactivity characterization of a spherically convergent ion focus. University of Wisconsin, Madison.
69. ^ "Stable, thermal equilibrium, large-amplitude, spherical plasma oscillations in electrostatic confinement devices", DC Barnes and Rick Nebel, PHYSICS OF PLASMAS VOLUME 5, NUMBER 7 JULY 1998
70. ^ Carr, M.; Khachan, J. (2013). "A biased probe analysis of potential well formation in an electron only, low beta Polywell magnetic field". Physics of Plasmas 20 (5): 052504. Bibcode2013PhPl...20e2504C. doi:10.1063/1.4804279
71. ^
72. ^ Cockburn & Ellyard 1981, pp. 48–50.
73. ^ Cockburn & Ellyard 1981, pp. 52–55.
74. ^ Oliphant, M. L. E.; Rutherford, Lord (3 July 1933). "Experiments on the Transmutation of Elements by Protons". Proceedings of the Royal Society A. 141 (843): 259–281. Bibcode:1933RSPSA.141..259O. doi:10.1098/rspa.1933.0117.
75. ^ Oliphant, M. L. E.; Kinsey, B. B.; Rutherford, Lord (1 September 1933). "The Transmutation of Lithium by Protons and by Ions of the Heavy Isotope of Hydrogen". Proceedings of the Royal Society A. 141 (845): 722–733. Bibcode:1933RSPSA.141..722O. doi:10.1098/rspa.1933.0150.
76. ^ Oliphant, M. L. E.; Harteck, P.; Rutherford, Lord (1 May 1934). "Transmutation Effects Observed with Heavy Hydrogen". Proceedings of the Royal Society A. 144 (853): 692–703. Bibcode:1934RSPSA.144..692O. doi:10.1098/rspa.1934.0077.
77. ^ "British Patent 817681". V3.espacenet.com. Retrieved 2013-06-22.
78. ^ "This Day in Quotes: SEPTEMBER 16 – Too cheap to meter: the great nuclear quote debate". This day in quotes. 2009. Retrieved 2009-09-16.
79. ^ Pfau, Richard (1984) No Sacrifice Too Great: The Life of Lewis L. Strauss University Press of Virginia, Charlottesville, Virginia, p. 187 ISBN 978-0-8139-1038-3
80. ^ David Bodansky (2004). Nuclear Energy: Principles, Practices, and Prospects. Springer. p. 32. ISBN 978-0-387-20778-0. Retrieved 2008-01-31.
81. ^ Nathaniel Fisch. Edward Teller Centennial Symposium. p. 118. Retrieved 30 October 2014.
82. ^ "Personnel and Financial history of the Los Alamos Sherwood Program" E L Kemp, 1965, https://fas.org/sgp/othergov/doe/lanl/lib-www/la-pubs/00403632.pdf
83. ^ Lyman J Spitzer, "The Physics of Fully Ionized Gases" 1963
84. ^ "1964 New York World's Fair 1965 - Attractions - General Electric - Page Eight". www.nywf64.com. Archived from the original on October 30, 2014.
85. ^ "Nuclear Power: A Very Short Introduction" 2011, page 90, Maxwell Irvine
86. ^ Cartlidge, Edwin. The Secret World of Amateur Fusion. Physics World, March 2007: IOP Publishing Ltd, pp. 10-11. ISSN 0953-8585.
87. ^ US Patent 3,258,402 June 28, 1966
88. ^ US Patent 3,386,883 June 4, 1968
89. ^ Robert L. Hirsch, "Inertial-Electrostatic Confinement of Ionized Fusion Gases", Journal of Applied Physics, v. 38, no. 7, October 1967
90. ^ M.H. Key 1985 Nucl. Fusion 25 1351, doi:10.1088/0029-5515/25/9/063
91. ^ "A Piece of the sun" by Dan Clery, June 2014
92. ^ Long 1976, p. 25.
93. ^ Principals of plasma physics, Nicholas Krall, 1973, Page 273
94. ^ "Summary of results from the tandem mirror experiment, TMX group, February 26, 1981
95. ^ "TMX Major Project proposal" Fred Coensgen, January 12, 1977
96. ^ Booth, William. "Fusion's \$372-Million Mothball." Science [New York City] 9 Oct. 1987, Volume 238 ed.: 152-55. Print.
97. ^ Koppel, Niko (May 20, 2010). "Edwin E. Kintner, Nuclear Power Pioneer, Dies at 90". NYTimes.com. Retrieved 2014-08-24.
98. ^ "Dr. Donna Strickland | Science". Uwaterloo.ca. Archived from the original on 2014-01-11. Retrieved 2014-08-24.
99. ^ a b Dr. Matthew McKinzie; Christopher E. Paine (2000). "When peer review fails : The Roots of the National Ignition Facility (NIF) Debacle". National Resources Defense Council. Retrieved 30 October 2014.
100. ^ "Recent Progress on the Los Alamos Aurora ICF (Inertial Confinement Fusion) Laser System." L. A. Rosocha, L. S. Blair, Publication Date, 1987.
101. ^ "Los Alamos National Labs Aurora Laser Fusion Project | Hextek Corp". Hextek.com. 2014-06-20. Archived from the original on May 17, 2014. Retrieved 2014-08-24.
102. ^ Hasegawa, A., Comments on Plasma Physics and Controlled Fusion, 1987, vol. 1, p. 147.
103. ^ "Tore Supra". Archived from the original on November 15, 2012. Retrieved February 3, 2016.
104. ^ Wilford, John Noble (24 April 1989). "Fusion Furor: Science's Human Face". The New York Times.
105. ^
106. ^ a b Browne 1989
107. ^ Chang, Kenneth (2004-03-25). "US will give cold fusion a second look". The New York Times. Retrieved 2009-02-08.
108. ^
109. ^ William J. Broad (31 October 1989). "Despite Scorn, Team in Utah Still Seeks Cold-Fusion Clues". The New York Times. pp. C1.
110. ^ Alfred 2009
111. ^ "'Cold fusion' rebirth? New evidence for existence of controversial energy source" (Press release). American Chemical Society. Retrieved 30 October 2014.
112. ^ Hagelstein et al. 2004
113. ^ Feder 2005
114. ^
115. ^ Y-K Martin Peng, "Spherical Torus, Compact Fusion at Low Yield"., ORNL/FEDC-87/7 (December 1984)
116. ^ Sykes 1997, pg. B247
117. ^ a b Braams and Scott, pg. 225
118. ^ Sykes 2008, pg. 11
119. ^ Jarvis, O. N (2006-06-16). "Neutron measurements from the preliminary tritium experiment at JET (invited)". Review of Scientific Instruments. 63 (10): 4511–4516. doi:10.1063/1.1143707.
120. ^ Lindl, John; McCrory, Robert L.; Campbell, E. Michael (1992), "Progress Toward Ignition and Burn Propagation in Inertial Confinement Fusion" (PDF), Physics Today, 45 (9): 32–40, Bibcode:1992PhT....45i..32L, doi:10.1063/1.881318
121. ^ Lindl, John (1995-11-01). "Development of the indirect‐drive approach to inertial confinement fusion and the target physics basis for ignition and gain". Physics of Plasmas. 2 (11): 3933–4024. Bibcode:1995PhPl....2.3933L. doi:10.1063/1.871025. ISSN 1070-664X.
122. ^ Krall, N. A.; Coleman, M.; Maffei, K.; Lovberg, J.; Jacobsen, R.; Bussard, R. W. (1995). "Forming and maintaining a potential well in a quasispherical magnetic trap". Physics of Plasmas 2: 146.
123. ^ "Inertial electrostatic fusion (IEF): A clean energy future" (Microsoft Word document). Energy/Matter Conversion Corporation. Retrieved 2006-12-03.
124. ^ "Fundamental limitations on plasma fusions systems not in thermodynamic equilibrium" Thesis, Todd Rider, June 1995
125. ^ Nevins, William M. "Can Inertial Electrostatic Confinement Work beyond the Ion-ion Collisional Time Scale?" Physics of Plasmas 2.10 (1995): 3804-819. Print.
126. ^ ""IEC Lab Timeline" accessed 1-25-2014". Iec.neep.wisc.edu. Retrieved 30 October 2014.
127. ^ "A portable neutron/tunable X-ray source based on inertial electrostatic confinement", Nuclear Instruments and Methods in Physics Research, A 422 (1999) 16-20
128. ^ "NSD-GRADEL-FUSION - Neutron Generators". Nsd-fusion.com. Retrieved 2014-08-24.
129. ^ "The IEC star-mode fusion neutron source for NAA--status and next-step designs". Appl Radiat Isot 53 (4-5): 779–83. October 2000.
130. ^
131. ^ "Fusion nucléaire et striction axiale". Archived from the original on October 4, 2012. Retrieved October 4, 2012.
132. ^ "Output of Sandia Z Accelerator Climbs Closer to Fusion". Sandia.gov. August 1, 1997. Retrieved 2014-08-24.
133. ^ "Another dramatic climb toward fusion conditions for Sandia Z accelerator". Sandia.gov. Retrieved 2014-08-24.
134. ^ "High-Output Sandia Accelerator Able to Predict Nuclear Blast Physics". Sandia.gov. December 2, 1996. Retrieved 2014-08-24.
135. ^
136. ^ "What is ITER?". Archived from the original on May 27, 2010. Retrieved February 6, 2016.
137. ^ "Fusor Forums • Index page". Fusor.net. Retrieved 2014-08-24.
138. ^ "Build a Nuclear Fusion Reactor? No Problem". Clhsonline.net. 2012-03-23. Archived from the original on 2014-10-30. Retrieved 2014-08-24.
139. ^ Danzico, Matthew (2010-06-23). "Extreme DIY: Building a homemade nuclear reactor in NYC". BBC News. Retrieved 30 October 2014.
140. ^ Schechner, Sam (2008-08-18). "Nuclear Ambitions: Amateur Scientists Get a Reaction From Fusion - WSJ". Online.wsj.com. Archived from the original on 2015-10-11. Retrieved 2014-08-24.
141. ^ "Will's Amateur Science and Engineering: Fusion Reactor's First Light!". Tidbit77.blogspot.com. 2010-02-09. Retrieved 2014-08-24.
142. ^ Taleyarkhan, R. P.; C. D. West; J. S. Cho; R. T. Lahey; Jr. R. Nigmatulin; R. C. Block (2002-03-08). "Evidence for Nuclear Emissions During Acoustic Cavitation". Science. 295 (1868): 1868–73. Bibcode:2002Sci...295.1868T. doi:10.1126/science.1067589. PMID 11884748. Archived from the original on November 6, 2005. Retrieved 2007-05-13.
143. ^ Purdue physicist found guilty of misconduct, Los Angeles Times, July 19, 2008, Thomas H. Maugh II
144. ^ a b Reich, Eugenie Samuel (23 November 2009). "Bubble-fusion scientist debarred from federal funding". Nature. doi:10.1038/news.2009.1103.
145. ^ "The Year in Science: Physics". 2006-10-21. Archived from the original on October 21, 2006. Retrieved 2013-06-22.
146. ^ "Equilibrium and low-frequency stability of a uniform density, collisionless, spherical Vlasov system" DC Barns, L Chacon, Physics of plasma November 2002
147. ^ "Observation of Spherical Focus in an Electron Penning Trap", T. B. Mitchell and M. M. Schauer, PHYSICAL REVIEW LETTERS, VOLUME 78, NUMBER 1
148. ^ Ph.D. Thesis "Improving Particle Confinement in Inertial Electrostatic Fusion for Spacecraft Power and Propulsion", Carl Dietrich, MASSACHUSETTS INSTITUTE OF TECHNOLOGY FEBRUARY 2007
149. ^ Ph.D. Thesis "Improved lifetimes and synchronization behavior in Mutlt-grid IEC fusion devices", Tom McGuire, MASSACHUSETTS INSTITUTE OF TECHNOLOGY FEBRUARY 2007
150. ^ "Phoenix Nuclear Labs meets neutron production milestone", PNL press release May 1, 2013, Ross Radel, Evan Sengbusch
151. ^ SirPhilip (posting an e-mail from "RW Bussard") (2006-06-23). "Fusion, eh?". James Randi Educational Foundation forums. Retrieved 2006-12-03.
152. ^ "The Advent of Clean Nuclear Fusion: Super-performance Space Power and Propulsion", Robert W. Bussard, Ph.D., 57th International Astronautical Congress, October 2–6, 2006
153. ^ Dutton, Judy. "Teen Nuclear Scientist Fights Terror", CNN.com, September 1, 2011. Retrieved September 3, 2011.
154. ^ "Rock Center: 19-year-old hopes to revolutionize nuclear power". NBC. Retrieved October 18, 2013.
155. ^ TED2013. "Taylor Wilson: My radical plan for small nuclear fission reactors". TED.com. Retrieved May 6, 2013.
156. ^ May, Kate Torgovnick (February 27, 2013). "Good energy comes in small packages: Taylor Wilson at TED2013". TED blog — Science. TED (conference). Retrieved 2014-02-10.
157. ^ "President Obama Hosts the White House Science Fair". The White House. Retrieved October 18, 2013.
158. ^ What is NIF?, Lawrence Livermore National Laboratory.
159. ^ a b Clery, Daniel (2014-07-25). "Fusion's restless pioneers". Science. 345 (6195): 370–375. doi:10.1126/science.345.6195.370. ISSN 0036-8075. PMID 25061186.
160. ^ a b c Frochtzwajg, Jonathan. "The secretive, billionaire-backed plans to harness fusion". Retrieved 2017-08-21.
161. ^ Kanellos, Michael. "Hollywood, Silicon Valley and Russia Join Forces on Nuclear Fusion". Forbes. Retrieved 2017-08-21.
162. ^ Gray, Richard. "The British reality TV star building a fusion reactor". Retrieved 2017-08-21.
163. ^ Seaver, Lynda L. (2010-10-01). "World's largest laser sets records for neutron yield and laser energy". Lawrence Livermore National Laboratory. Retrieved 2013-06-22.
164. ^ "First successful integrated experiment at National Ignition Facility announced". General Physics. PhysOrg.com. October 8, 2010. Retrieved 2010-10-09.
165. ^ SPIE Europe Ltd. "PW 2012: fusion laser on track for 2012 burn". Optics.org. Retrieved 2013-06-22.
166. ^ "Nuclear fusion milestone passed at US lab". BBC News. Retrieved 30 October 2014.
167. ^ "ADVANCES TOWARDS PB11 FUSION WITH THE DENSE PLASMA FOCUS", Eric Lerner, Lawrenceville Plasma Physics, 2008
168. ^ Kramer, David (2006-06-16). "Livermore ends LIFE". Physics Today. 67 (4): 26–27. doi:10.1063/PT.3.2344.
169. ^ "The Alectryon High Yield Neutron Generator". Phoenix Nuclear Labs. 2013.
170. ^ "FuseNet: The European Fusion Education Network". Fusenet.eu. Retrieved 30 October 2014.
171. ^ "Fusion Power Could Happen Sooner Than You Think". Popular Science. Popular Science. 2013. Retrieved 30 October 2014.
172. ^ "Nuclear fusion energy in a decade? Lockheed Martin is betting on it". Washington Post. 2014-10-15. Retrieved 30 October 2014.
173. ^ a b Wang, Brian (August 1, 2018). "Nuclear Fusion Updated project reviews". www.nextbigfuture.com. Retrieved 2018-08-03.
174. ^ "Microsoft Research – Emerging Technology, Computer, and Software Research". Microsoft Research.
175. ^ Chandler, David L. (10 August 2015). "A small, modular, efficient fusion plant". MIT News. MIT News Office.
176. ^ "Wendelstein W7-X starting its experimental journey". Germany: ipp.mpg.de.
177. ^ Clery, Daniel (2017-04-28). "Private fusion machines aim to beat massive global effort". Science. 356 (6336): 360–361. doi:10.1126/science.356.6336.360. ISSN 0036-8075. PMID 28450588.
178. ^ Gibbs, W. Wayt (2016). "The Fusion Underground". Scientific American. 315 (5): 38–45. Bibcode:2016SciAm.315e..38G. doi:10.1038/scientificamerican1116-38. PMID 27918497.
179. ^ MacDonald, Fiona. "The UK Just Switched on an Ambitious Fusion Reactor - And It Works". ScienceAlert. Retrieved 2019-07-03.
180. ^ "Italy's Eni defies sceptics, may up stake in nuclear fusion project". Reuters. 13 April 2018.
181. ^ "MIT Aims to Harness Fusion Power Within 15 years". 3 April 2018.
182. ^ "MIT Aims To Bring Nuclear Fusion To The Market In 10 Years". 9 March 2018.
183. ^
184. ^ uk-wants-to-build-worlds-first-fusion-power-plant-20-years-from-now 2019
185. ^ Gibney, Elizabeth (2019-10-11). "UK hatches plan to build world's first fusion power plant". Nature. doi:10.1038/d41586-019-03039-9.
186. ^ Atzeni, Stefano; Meyer-ter-Vehn, Jürgen (3 June 2004). The Physics of Inertial Fusion: BeamPlasma Interaction, Hydrodynamics, Hot Dense Matter. OUP Oxford. pp. 12–13. ISBN 978-0-19-152405-9.
187. ^ "Thinkquest: D-T reaction". Retrieved 12 June 2010.
188. ^ Iiyoshi, A; H. Momota; O Motojima; et al. (October 1993). "Innovative Energy Production in Fusion Reactors". National Institute for Fusion Science NIFS: 2–3. Retrieved 14 February 2012.
189. ^ "Nuclear Fusion Power, Assessing fusion power". World-nuclear.org. Retrieved 30 October 2014.
190. ^ Rolfe, A. C. (1999). "Remote Handling JET Experience" (PDF). Nuclear Energy. 38 (5): 6. ISSN 0140-4067. Retrieved 10 April 2012.
191. ^ M. Sawan, S. Zinkle, and J. Sheffield, Fusion Eng Des 61-2, 561 (2002).
192. ^ J. Kesner, D. Garnier, A. Hansen, M. Mauel, and L. Bromberg, Nucl Fusion 2004; 44, 193
193. ^ Heindler and Kernbichler, Proc. 5th Intl. Conf. on Emerging Nuclear Energy Systems, 1989, pp. 177–82. See also Residual radiation from a p–11B reactor
194. ^ "Nuclear Fusion: Laser-Beam Experiment Yields Exciting Results". LiveScience.com.
195. ^ "Record proton-boron fusion rate achieved - FuseNet". www.fusenet.eu.
196. ^ a b "Thermal response of nanostructured tungsten"Shin Kajita, et al., January 2014, Nucl. Fusion 54 (2014) 033005 (10pp)
197. ^ Evans, Ll. M.; Margetts, L.; Casalegno, V.; Lever, L. M.; Bushell, J.; Lowe, T.; Wallwork, A.; Young, P.; Lindemann, A. (2015-05-28). "Transient thermal finite element analysis of CFC–Cu ITER monoblock using X-ray tomography data". Fusion Engineering and Design. 100: 100–111. doi:10.1016/j.fusengdes.2015.04.048.
198. ^ Evans, Ll. M.; Margetts, L.; Casalegno, V.; Leonard, F.; Lowe, T.; Lee, P. D.; Schmidt, M.; Mummery, P. M. (2014-06-01). "Thermal characterisation of ceramic/metal joining techniques for fusion applications using X-ray tomography". Fusion Engineering and Design. 89 (6): 826–836. doi:10.1016/j.fusengdes.2014.05.002.
199. ^ Dulon, Krista (2012). "Who is afraid of ITER?". iter.org. Retrieved 18 August 2012.
200. ^ a b McCracken, Garry; Stott, Peter (8 June 2012). Fusion: The Energy of the Universe. Academic Press. pp. 198–199. ISBN 978-0-12-384656-3. Retrieved 18 August 2012.
201. ^ Angelo, Joseph A. (30 November 2004). Nuclear Technology. Greenwood Publishing Group. p. 474. ISBN 978-1-57356-336-9. Retrieved 18 August 2012.
202. ^ a b T. Hamacher; A.M. Bradshaw (October 2001). "Fusion as a Future Power Source: Recent Achievements and Prospects" (PDF). World Energy Council. Archived from the original (PDF) on 2004-05-06.
203. ^
204. ^ Peterson, Tom. "Explain it in 60 seconds: Magnet Quench". Symmetry Magazine. Fermilab/SLAC. Retrieved 15 February 2013.
205. ^ Petrangeli, Gianni (1 January 2006). Nuclear Safety. Butterworth-Heinemann. p. 430. ISBN 978-0-7506-6723-4.
206. ^ Markandya, Anil; Wilkinson, Paul (2007). "Electricity generation and health". The Lancet. 370: 979–990.
207. ^ a b c d R. J. Goldston, A. Glaser, A. F. Ross: "Proliferation Risks of Fusion Energy: Clandestine Production, Covert Production, and Breakout";9th IAEA Technical Meeting on Fusion Power Plant Safety (accessible at no cost, 2013) and Glaser, A.; Goldston, R. J. (2012). "Proliferation risks of magnetic fusion energy: Clandestine production, covert production and breakout". Nuclear Fusion. 52 (4): 043004. Bibcode:2012NucFu..52d3004G. doi:10.1088/0029-5515/52/4/043004.
208. ^ a b "Strong Neutron Sources - How to cope with weapon material production capabilities of fusion and spallation neutron sources?" Archived 2014-02-24 at the Wayback Machine Matthias Englert, Giorgio Franceschini, Wolfgang Liebert (2011); 7th INMM/Esarda Workshop, Aix‐en‐Provence
209. ^ "Energy for Future Centuries" (PDF). Archived from the original (PDF) on 2011-07-27. Retrieved 2013-06-22.
210. ^ Eric Christian; et al. "Cosmicopia". NASA. Retrieved 2009-03-20.
211. ^ Fusion For Energy. "Fusion For Energy - Bringing the power of the sun to earth". f4e.europa.eu.
212. ^ "The current EU research programme" (PDF). FP6. Tab Beim Bundestag (tab.fzk.de). Retrieved 30 October 2014.
213. ^ "The Sixth Framework Programme in brief" (PDF). ec.europa.eu. Retrieved 30 October 2014.
214. ^ Grossman, Lev (November 2, 2015). "Star power". Time.
215. ^ Robert F. Heeter; et al. "Conventional Fusion FAQ Section 2/11 (Energy) Part 2/5 (Environmental)". Fused.web.llnl.gov. Archived from the original on 3 March 2001. Retrieved 30 October 2014.
216. ^ Frank J. Stadermann. "Relative Abundances of Stable Isotopes". Laboratory for Space Sciences, Washington University in St. Louis. Archived from the original on 2011-07-20.
217. ^ J. Ongena; G. Van Oost. "Energy for Future Centuries" (PDF). Laboratorium voor Plasmafysica– Laboratoire de Physique des Plasmas Koninklijke Militaire School– École Royale Militaire; Laboratorium voor Natuurkunde, Universiteit Gent. pp. Section III.B. and Table VI. Archived from the original (PDF) on 2011-07-27.
218. ^ EPS Executive Committee. "The importance of European fusion energy research". The European Physical Society. Archived from the original on 2008-10-08.
219. ^ Sing Lee; Sor Heoh Saw. "Nuclear Fusion Energy-Mankind's Giant Step Forward" (PDF). HPlasmafocus.net. Retrieved 30 October 2014.
220. ^ "What Is The Future Of Space Travel?". Zidbits. Retrieved 14 November 2015.