|Part of a series on|
The energy efficiency in transport is the useful travelled distance, of passengers, goods or any type of load; divided by the total energy put into the transport propulsion means. The energy input might be rendered in several different types depending on the type of propulsion, and normally such energy is presented in liquid fuels, electrical energy or food energy. The energy efficiency is also occasionally known as energy intensity. The inverse of the energy efficiency in transport, is the energy consumption in transport.
Energy efficiency in transport is often described in terms of fuel consumption, fuel consumption being the reciprocal of fuel economy. Nonetheless, fuel consumption is linked with a means of propulsion which uses liquid fuels, whilst energy efficiency is applicable to any sort of propulsion. To avoid said confusion, and to be able to compare the energy efficiency in any type of vehicle, experts tend to measure the energy in the International System of Units, i.e., Joules.
Therefore, in the International System of Units, the energy efficiency in transport is measured in terms of metre per Joule, or m/J, whilst the energy consumption in transport is measured in terms of Joules per meter, or J/m. The more efficient the vehicle, the more metres it covers with one Joule (more efficiency), or the less Joules it uses to travel over one meter (less consumption). The energy efficiency in transport largely varies by means of transport. Different types of transport range from some hundred kilojoules per kilometre (kJ/km) for a bicycle to tens of megajoules per kilometer (MJ/km) for a helicopter.
Via type of fuel used and rate of fuel consumption, energy efficiency is also often related to operating cost ($/km) and environmental emissions (e.g. CO2/km).
- 1 Units of measurement
- 2 Overview
- 3 Land transport means
- 4 Air transport means
- 5 Water transport means
- 6 International transport comparisons
- 7 See also
- 8 Footnotes
- 9 External links
Units of measurement
In the International System of Units, the energy efficiency in transport is measured in terms of metre per Joule, or m/J. Nonetheless, several conversions are applicable, depending on the unit of distance and on the unit of energy. For liquid fuels, normally the quantity of energy input is measured in terms of the liquid's volume, such as litres or gallons. For propulsion which runs on electricity, normally kW·h is used, whilst for any type of human-propelled vehicle, the energy input is measured in terms of Calories. Conversions between different types of energy and units, are very well known in the art.
For passenger transport, the energy efficiency is normally measured in terms of passengers times distance per unit of energy, in the SI, passengers metres per Joule (pax.m/J); whilst for cargo transport the energy efficiency is normally measured in terms of mass of transported cargo times distance per unit of energy, in the SI, kilograms metres per Joule (kg.m/J).
Typical conversions into SI unit
|Litre of gasoline||0.3x10⁸|
|US gallon of gasoline||1.3x10⁸|
|Imp. gallon of gasoline||1.6x10⁸|
Energy efficiency is expressed in terms of fuel economy:
- distance per vehicle per unit fuel volume; e.g., km/L or miles per gallon (US or imperial).
- distance per vehicle per unit fuel mass; e.g., km/kg.
- distance per vehicle per unit energy; e.g., miles per gallon equivalent (mpg-e).
- volume of fuel (or total energy) consumed per unit distance per vehicle; e.g. L/100 km or MJ/100 km.
- volume of fuel (or total energy) consumed per unit distance per passenger; e.g., L/(100 passenger·km).
- volume of fuel (or total energy) consumed per unit distance per unit mass of cargo transported; e.g., L/100 kg·km or MJ/t·km.
- electrical energy used per vehicle per unit distance; e.g., kW·h/100 km.
Note that producing electricity from fuel requires much more primary energy than the amount of electricity produced.
- calories burnt by the body's metabolism per kilometre; e.g., Cal/km.
- calories burnt by the body's metabolism per mile; e.g., Cal/miles.
In the following table the energy efficiency and energy consumption for different types of passenger land vehicles and modes of transport, as well as standard occupancy rates, are presented. The sources for these figures are in the correspondent section for each vehicle, in the following article. The conversions amongst different types of units, are well known in the art.
For the conversion amongst units of energy in the following table, 1 litre of gasoline amounts to 34.2 MJ, 1 kWh amounts to 3.6 MJ and 1 kilocalorie amounts to 4184 J. For the car occupation ratio, the value of 1.2 passengers per automobile was considered. Nonetheless in Europe this value slightly increases to 1.4. The sources for conversions amongst units of measurements appear only of the first row.
Land Passenger Transport means
|Mode of transport||Energy Efficiency||Energy consumption||Average number of passengers per vehicle||Energy Efficiency||Energy consumption|
|mpg(US) of gasoline||mpg(imp) of gasoline||km/L of gasoline||km/MJ||m/J||L(gasoline)/ 100 km||kWh/100 km||Cal/km||MJ/100 km||J/m||(m.pax)/J||J/(m.pax)|
|Electric kick scooter||24.87||0.02487||1.12||9.61||4.00||40||1.0||0.02487||40.21|
|General Motors EV1||97.15||116.68||41.30||1.21||0.00121||2.42||23.00||197.90||82.80||828||1.2||0.00145||690.00|
|SEAT Ibiza 1.4 TDI Ecomotion||61.88||74.31||26.31||0.77||0.00077||3.80||36.11||310.71||130.00||1300||1.2||0.00092||1083.33|
|Tesla Model S||129.54||155.57||55.07||1.61||0.00161||1.82||17.25||148.42||62.10||621||1.2||0.00193||517.50|
|Proterra 40' E2||0.23[note 1]||0.00023||121.54||1044.20||437.60||4376||11.0||0.00319||313.48|
|JR East (jp)||~||0.01091||91.67|
- The range used is the midpoint of the effective operating range.
Land transport means
A 68 kg (150 lb) person walking at 4 km/h (2.5 mph) requires approximately 210 kilocalories (880 kJ) of food energy per hour, which is equivalent to 4.55 km/MJ. 1 US gal (3.8 L) of gasoline contains about 114,000 British thermal units (120 MJ) of energy, so this is approximately equivalent to 360 miles per US gallon (0.65 L/100 km).
Velomobiles have the highest energy efficiency of any known mode of personal transport because of their small frontal area and aerodynamic shape. At a speed of 50 km/h (31 mph), the velomobile manufacturer WAW claims that only 0.5 kW·h (1.8 MJ) of energy per 100 km is needed to transport the passenger (= 18 J/m). This is around 1⁄5 (20%) of what is needed to power a standard upright bicycle without aerodynamic cladding at same speed, and 1⁄50 (2%) of that which is consumed by an average fossil fuel or electric car (the velomobile efficiency corresponds to 4700 miles per US gallon, 2000 km/L, or 0.05 L/100 km). Real energy from food used by human is 4-5 times more. Unfortunately their energy use advantage over bicycles is smaller with decrease of speed and disappear at around 10 km/h where power needed for velomobile and triathlon bike is almost the same
A standard lightweight, moderate-speed bicycle is one of the most energy-efficient forms of transport. Compared with walking, a 64 kg (140 lb) cyclist riding at 16 km/h (10 mph) requires about half the food energy per unit distance: 27 kcal/km, 3.1 kW⋅h (11 MJ) per 100 km, or 43 kcal/mi. This converts to about 732 mpg‑US (0.321 L/100 km; 879 mpg‑imp). This means that a bicycle will use between 10-25 times less energy per distance traveled than a personal car, depending on fuel source and size of the car. This figure does depend on the speed and mass of the rider: greater speeds give higher air drag and heavier riders consume more energy per unit distance. In addition, because bicycles are very lightweight (usually between 7–15 kg) this means they consume very low amounts of materials and energy to manufacture. In comparison to an automobile weighing 1500 kg or more, a bicycle typically requires 100-200 times less energy to produce than an automobile. In addition, bicycles require less space both to park and to operate and they damage road surfaces less, adding an infrastructural factor of efficiency.
A motorized bicycle allows human power and the assistance of a 49 cm3 (3.0 cu in) engine, giving a range of 160 to 200 mpg‑US (1.5–1.2 L/100 km; 190–240 mpg‑imp). Electric pedal-assisted bikes run on as little as 1.0 kW⋅h (3.6 MJ) per 100 km, while maintaining speeds in excess of 30 km/h (19 mph). These best-case figures rely on a human doing 70% of the work, with around 3.6 MJ (1.0 kW⋅h) per 100 km coming from the motor. This makes an electric bicycle one of the most efficient possible motorized vehicles, behind only a motorized velomobile.
Electric kick scooter
Electric kick scooters, such as those used by scooter-sharing systems like Bird or Lime, typically have a maximum range of under 30 km (19 mi) and a maximum speed of roughly 15.5 mph (24.9 km/h). Intended to fit into a last mile niche and be ridden in bike lanes, they require little skill from the rider. Because of their light weight and small motors, they are extremely energy-efficient with a typical energy efficiency of 1.1 kW⋅h (4.0 MJ) per 100 km (1904 MPGe 810 km/l 0.124 l/100 km), even more efficient than bicycles and walking. However, as they must be recharged frequently, they are often collected overnight with motor vehicles, somewhat negating this efficiency. The lifecycle of electric scooters is also notably shorter than that of bicycles, often reaching only a single digit number of years.
To be thorough, a comparison must also consider the energy costs of producing, transporting and packaging of fuel (food or fossil fuel), the energy incurred in disposing of exhaust waste, and the energy costs of manufacturing the vehicle. This last can be significant given that walking requires little or no special equipment, while automobiles, for example, require a great deal of energy to produce and have relatively short lifespans. In addition, any comparison of electric vehicles and liquid-fuelled vehicles must include the fuel consumed in the power station to generate the electricity. In the UK for instance the efficiency of the electricity generation and distribution system is around 0.40.
The automobile is an inefficient vehicle compared to other modes of transport. This is because the ratio between the mass of the vehicle and the mass of the passengers is much higher when compared to other modes of transport.
Automobile fuel efficiency is most commonly expressed in terms of the volume of fuel consumed per one hundred kilometres (L/100 km), but in some countries (including the United States, the United Kingdom and India) it is more commonly expressed in terms of the distance per volume fuel consumed (km/L or miles per gallon). This is complicated by the different energy content of fuels such as petrol and diesel. The Oak Ridge National Laboratory (ORNL) states that the energy content of unleaded gasoline is 115,000 British thermal unit (BTU) per US gallon (32 MJ/L) compared to 130,500 BTU per US gallon (36.4 MJ/L) for diesel.
A second important consideration is the energy costs of producing energy. Bio-fuels, electricity and hydrogen, for instance, have significant energy inputs in their production. Hydrogen production efficiency are 50-70% when produced from natural gas, and 10-15% from electricity. The efficiency of hydrogen production, as well as the energy required to store and transport hydrogen, must to be combined with the vehicle efficiency to yield net efficiency. Because of this, hydrogen automobiles are one of the least efficient means of passenger transport, generally around 50 times as much energy must be put into the production of hydrogen compared to how much is used to move the car.
A third consideration to take into account when calculating energy efficiency of automobiles is the occupancy rate of the vehicle. Although the consumption per unit distance per vehicle increases with increasing number of passengers, this increase is slight compared to the reduction in consumption per unit distance per passenger. This means that higher occupancy yields higher energy efficiency per passenger. Automobile occupancy varies across regions. For example, the estimated average occupancy rate is about 1.3 passengers per car in the San Francisco Bay Area, while the 2006 UK estimated average is 1.58.
Fourth, the energy needed to build and maintain roads is an important consideration, as is the energy returned on energy invested (EROEI). Between these two factors, roughly 20% must be added to the energy of the fuel consumed, to accurately account for the total energy used.
Finally, vehicle energy efficiency calculations would be misleading without factoring the energy cost of producing the vehicle itself. This initial energy cost can of course be depreciated over the life of the vehicle to calculate an average energy efficiency over its effective life span. In other words, vehicles that take a lot of energy to produce and are used for relatively short periods will require a great deal more energy over their effective lifespan than those that do not, and are therefore much less energy efficient than they may otherwise seem. Hybrid and electric cars use less energy in their operation than comparable petroleum-fueled cars but more energy is used to manufacture them, so the overall difference would be less than immediately apparent. Compare, for example, walking, which requires no special equipment at all, and an automobile, produced in and shipped from another country, and made from parts manufactured around the world from raw materials and minerals mined and processed elsewhere again, and used for a limited number of years. According to the French energy and environment agency ADEME, an average motor car has an embodied energy content of 20,800 kWh and an average electric vehicle amounts to 34,700 kWh. The electric car requires nearly twice as much energy to produce, primarily due to the large amount of mining and purification necessary for the rare earth metals and other materials used in lithium-ion batteries and in the electric drive motors. This represents a significant portion of the energy used over the life of the car (in some cases nearly as much as energy that is used through the fuel that is consumed, effectively doubling the car's per-distance energy consumption), and cannot be ignored when comparing automobiles to other transport modes. It is important to note, also, that as these are average numbers for French automobiles and they are likely to be significantly larger in more auto-centric countries like the United States and Canada, where much larger and heavier cars are more common.
On a percentage basis, if there is one occupant in an automobile, between 0.4-0.6% of the total energy used is used to move the person in the car, while 99.4-99.6% (about 165 to 250 times more) is used to move the car.
Example consumption figures
- Solar cars use no externally supplied fuel other than sunlight, charging the batteries entirely from built-in solar panels, and typically use less than 3 kW·h per 100 miles (67 kJ/km or 1.86 kW·h/100 km). These cars are not designed for passenger or utility use and would not be practical as such due to speed, payload, and inherent design.
- The four passenger GEM NER uses 169 Wh/mi (203 mpg‑e; 10.5 kW⋅h/100 km), which equates to 2.6 kW·h/100 km per person when fully occupied, albeit at only 24 mph (39 km/h).
- The General Motors EV1 was rated in a test with a charging efficiency of 373 Wh-AC/mile or 23 kWh/100 km approximately equivalent to 2.6 L/100 km (110 mpg‑imp; 90 mpg‑US) for petroleum-fuelled vehicles.
- Chevrolet Volt in full electric mode uses 36 kilowatt-hours per 100 miles (810 kJ/km; 96 mpg‑e), meaning it may approach or exceed the energy efficiency of walking if the car is fully occupied with 4 or more passengers, although the relative emissions produced may not follow the same trends if analyzing environmental impacts.
- The Daihatsu Charade 993cc turbo diesel (1987–1993) won the most fuel efficient vehicle award for going round the United Kingdom consuming an average of 2.82 L/100 km (100 mpg‑imp). It was surpassed only recently by the VW Lupo 3 L which consumes about 2.77 L/100 km (102 mpg‑imp). Both cars are rare to find on the popular market. The Daihatsu had major problems with rust and structural safety which contributes to its rarity and the quite short production run.
- The Volkswagen Polo 1.4 TDI Bluemotion and the SEAT Ibiza 1.4 TDI Ecomotion, both rated at 3.8 L/100 km (74 mpg‑imp; 62 mpg‑US) (combined) were the most fuel efficient petroleum-fueled cars on sale in the UK as of 22 March 2008.[needs update]
- Honda Insight – achieves 48 mpg‑US (4.9 L/100 km; 58 mpg‑imp) under real-world conditions.
- Honda Civic Hybrid- regularly averages around 45 mpg‑US (5.2 L/100 km; 54 mpg‑imp).
- 2012 Cadillac CTS-V Wagon 6.2 L Supercharged, 14 mpg‑US (17 L/100 km; 17 mpg‑imp).
- 2012 Bugatti Veyron, 10 mpg‑US (24 L/100 km; 12 mpg‑imp).
- 2018 Honda Civic: 36 mpg‑US (6.5 L/100 km; 43 mpg‑imp) 
- 2017 Mitsubishi Mirage: 39 mpg‑US (6.0 L/100 km; 47 mpg‑imp) 
- 2017 Hyundai Ioniq hybrid: 55 mpg‑US (4.3 L/100 km; 66 mpg‑imp)
- 2017 Toyota Prius: 56 mpg‑US (4.2 L/100 km; 67 mpg‑imp) (Eco trim)
- 2018 Nissan Leaf: 30 kWh (110 MJ)/100 mi (671 kJ/km) or 112 MPGe 
- 2017 Hyundai Ioniq EV: 25 kWh (90 MJ)/100 mi (560 kJ/km) or 136 MPGe
Trains are in general one of the most efficient means of transport for freight and passengers. An inherent efficiency advantage is the low friction of steel wheels on steel rails compared especially to rubber tires on asphalt. Efficiency varies significantly with passenger loads, and losses incurred in electricity generation and supply (for electrified systems), and, importantly, end-to-end delivery, where stations are not the originating final destinations of a journey.
Actual consumption depends on gradients, maximum speeds, and loading and stopping patterns. Data produced for the European MEET project (Methodologies for Estimating Air Pollutant Emissions) illustrate the different consumption patterns over several track sections. The results show the consumption for a German ICE high-speed train varied from around 19 to 33 kW⋅h/km (68–119 MJ/km; 31–53 kW⋅h/mi). The data also reflects the weight of the train per passenger. For example, TGV double-deck Duplex trains use lightweight materials, which keep axle loads down and reduce damage to track and also save energy.
The specific energy consumption of the trains worldwide amounts to about 150 kJ/pkm (kilojoule per passenger kilometre) and 150 kJ/tkm (kilojoule per tonne kilometre) (ca. 4.2 kWh/100 pkm and 4.2 kWh/100 tkm) in terms of final energy. Passenger transportation by rail systems requires less energy than by car or plane (one seventh of the energy needed to move a person by car in an urban context,). This is the reason why, although accounting for 9% of world passenger transportation activity (expressed in pkm) in 2015, rail passenger services represented only 1% of final energy demand in passenger transportation.
Energy consumption estimates for rail freight vary widely, and many are provided by interested parties. Some are tabulated below.
|Country||Year||Fuel economy (weight of goods)||Energy Intensity|
|USA||2007||185.363 km/L (1 short ton)||energy/mass-distance|
|USA||2018||473 miles/gallon (1 ton)||energy/mass-distance|
|UK||—||87 t·km/L||0.41 MJ/t·km (LHV)|
|Country||Year||Train efficiency||Per passenger-km (kJ)||Note|
|China||2018||9.7 MJ (2.7 kWh) /car-km||137 kJ/passenger-km (at 100% load)||[email protected] km/h|
Beijing-Shanghai PDL 1302 km average
|Japan||2004||17.9 MJ (5.0 kWh)/car-km||350 kJ/passenger-km||JR East average|
|Japan||2017||1.49 kWh/car-km||≈92 kJ/passenger-km||JR East Conventional Rail|
|EC||1997||18 kW⋅h/km (65 MJ/km)|
|USA||1.125 mpg‑US (209.1 L/100 km; 1.351 mpg‑imp)||468 passenger-miles/US gallon (0.503 L/100 passenger-km)|
|Switzerland||2011||2300 GWhr/yr||470 kJ/passenger-km|
|Basel, Switzerland||1.53 kWh/vehicle-km (5.51 MJ/vehicle-km)||85 kJ/passenger-km (150 kJ/passenger-km at 80% average load)|
|USA||2009||2,435 BTU/mi (1.60 MJ/km)|
|Portugal||2011||8.5 kW⋅h/km (31 MJ/km; 13.7 kW⋅h/mi)||77 kJ/passenger-km|
Stopping is a considerable source of inefficiency. Modern electric trains like the Shinkansen (the Bullet Train) use regenerative braking to return current into the catenary while they brake. A Siemens study indicated that regenerative braking might recover 41.6% of the total energy consumed. The Passenger Rail (Urban and Intercity) and Scheduled Intercity and All Charter Bus Industries Technological and Operational Improvements – FINAL REPORT states that "Commuter operations can dissipate more than half of their total traction energy in braking for stops." and that "We estimate head-end power to be 35 percent (but it could possibly be as high as 45 percent) of total energy consumed by commuter railways." Having to accelerate and decelerate a heavy train load of people at every stop is inefficient despite regenerative braking which can recover typically around 20% of the energy wasted in braking. Weight is a determinant of braking losses.
- In July 2005, the average occupancy for buses in the UK was stated to be 9 passengers per vehicle.
- The fleet of 244 40-foot (12 m) 1982 New Flyer trolley buses in local service with BC Transit in Vancouver, Canada, in 1994/95 used 35,454,170 kWh for 12,966,285 vehicle km, or 9.84 MJ/vehicle km. Exact ridership on trolleybuses is not known, but with all 34 seats filled this equates to 0.32 MJ/passenger km. It is quite common to see people standing on Vancouver trolleybuses. This is a service with many stops per kilometre; part of the reason for the efficiency is the use of regenerative braking.
- A commuter service in Santa Barbara, California, USA, found average diesel bus efficiency of 6.0 mpg‑US (39 L/100 km; 7.2 mpg‑imp) (using MCI 102DL3 buses). With all 55 seats filled this equates to 330 passenger mpg; with 70% filled, 231 passenger mpg.
- In 2011 the fleet of 752 buses in the city of Lisbon had an average speed of 14.4 km/h and an average occupancy of 20.1 passengers per vehicle.
- Battery electric buses combine the high efficiency of a trolleybus with the flexibility of a diesel bus. Major manufacturers include BYD and Proterra.
- NASA's Crawler-Transporter is used to move the Shuttle from storage to the launch pad. It uses diesel and has one of the highest fuel consumption rates on record, 150 US gallons per mile (350 l/km; 120 imp gal/mi).
Air transport means
A principal determinant of energy consumption in aircraft is drag, which must be opposed by thrust for the aircraft to progress.
- Drag is proportional to the lift required for flight, which is equal to the weight of the aircraft. As induced drag increases with weight, mass reduction, with improvements in engine efficiency and reductions in aerodynamic drag, has been a principal source of efficiency gains in aircraft, with a rule-of-thumb being that a 1% weight reduction corresponds to around a 0.75% reduction in fuel consumption.
- Flight altitude affects engine efficiency. Jet-engine efficiency increases at altitude up to the tropopause, the temperature minimum of the atmosphere; at lower temperatures, the Carnot efficiency is higher. Jet engine efficiency is also increased at high speeds, but above about Mach 0.85 the airframe aerodynamic losses increase faster.
- Compressibility effects: beginning at transonic speeds of around Mach 0.85, shockwaves form increasing drag.
- For supersonic flight, it is difficult to achieve a lift to drag ratio greater than 5, and fuel consumption is increased in proportion.
Passenger airplanes averaged 4.8 l/100 km per passenger (1.4 MJ/passenger-km) (49 passenger-miles per gallon) in 1998. Note that on average 20% of seats are left unoccupied. Jet aircraft efficiencies are improving: Between 1960 and 2000 there was a 55% overall fuel efficiency gain (if one were to exclude the inefficient and limited fleet of the DH Comet 4 and to consider the Boeing 707 as the base case). Most of the improvements in efficiency were gained in the first decade when jet craft first came into widespread commercial use. Compared to advanced piston engine airliners of the 1950s, current jet airliners are only marginally more efficient per passenger-mile. Between 1971 and 1998 the fleet-average annual improvement per available seat-kilometre was estimated at 2.4%. Concorde the supersonic transport managed about 17 passenger-miles to the Imperial gallon; similar to a business jet, but much worse than a subsonic turbofan aircraft. Airbus puts the fuel rate consumption of their A380 at less than 3 l/100 km per passenger (78 passenger-miles per US gallon).
The mass of an aircraft can be reduced by using light-weight materials such as titanium, carbon fiber and other composite plastics. Expensive materials may be used, if the reduction of mass justifies the price of materials through improved fuel efficiency. The improvements achieved in fuel efficiency by mass reduction, reduces the amount of fuel that needs to be carried. This further reduces the mass of the aircraft and therefore enables further gains in fuel efficiency. For example, the Airbus A380 design includes multiple light-weight materials.
Airbus has showcased wingtip devices (sharklets or winglets) that can achieve 3.5 percent reduction in fuel consumption. There are wingtip devices on the Airbus A380. Further developed Minix winglets have been said to offer 6 percent reduction in fuel consumption. Winglets at the tip of an aircraft wing smooth out the wing-tip vortex (reducing the aircraft's wing drag) and can be retrofitted to any airplane.
NASA and Boeing are conducting tests on a 500 lb (230 kg) "blended wing" aircraft. This design allows for greater fuel efficiency since the whole craft produces lift, not just the wings. The blended wing body (BWB) concept offers advantages in structural, aerodynamic and operating efficiencies over today's more conventional fuselage-and-wing designs. These features translate into greater range, fuel economy, reliability and life cycle savings, as well as lower manufacturing costs. NASA has created a cruise efficient STOL (CESTOL) concept.
Fraunhofer Institute for Manufacturing Engineering and Applied Materials Research (IFAM) have researched a shark skin imitating paint that would reduce drag through a riblet effect. Aircraft are a major potential application for new technologies such as aluminium metal foam and nanotechnology such as the shark skin imitating paint.
Propeller systems, such as turboprops and propfans are a more fuel efficient technology than jets. But turboprops have an optimum speed below about 450 mph (700 km/h). This speed is less than used with jets by major airlines today. With the current [needs update] high price for jet fuel and the emphasis on engine/airframe efficiency to reduce emissions, there is renewed interest in the propfan concept for jetliners that might come into service beyond the Boeing 787 and Airbus A350XWB. For instance, Airbus has patented aircraft designs with twin rear-mounted counter-rotating propfans. NASA has conducted an Advanced Turboprop Project (ATP), where they researched a variable pitch propfan that produced less noise and achieved high speeds.
Related to fuel efficiency is the impact of aviation emissions on climate.
- Motor-gliders made of composite materials can reach an extremely low fuel consumption for cross-country flights, using thermal air currents and winds.
- At 160 km/h, a diesel powered two-seater Dieselis burns 6 liters of fuel per hour, 1.9 liters per 100 passenger km.
- at 220 km/h, a four-seater 100 hp MCR-4S burns 20 liters of gas per hour, 2.2 liters per 100 passenger km.
- Under continuous motorised flight at 225 km/h, a Pipistrel Sinus burns 11 liters of fuel per flight hour. Carrying 2 people aboard, it operates at 2.4 liters per 100 passenger km.
- Ultralight aircraft Tecnam P92 Echo Classic at cruise speed of 185 km/h burns 17 liters of fuel per flight hour, 4.6 liters per 100 passenger km (2 people). Other modern ultralight aircraft have increased efficiency; Tecnam P2002 Sierra RG at cruise speed of 237 km/h burns 17 liters of fuel per flight hour, 3.6 liters per 100 passenger km (2 people).
- Two-seater and four-seater flying at 250 km/h with old generation engines can burn 25 to 40 liters per flight hour, 3 to 5 liters per 100 passenger km.
- The Sikorsky S-76C++ twin turbine helicopter gets about 1.65 mpg‑US (143 L/100 km; 1.98 mpg‑imp) at 140 knots (260 km/h; 160 mph) and carries 12 for about 19.8 passenger-miles per gallon (11.9 L per 100 passenger km).
Water transport means
Cunard stated that Queen Elizabeth 2 travelled 49.5 feet per imperial gallon of diesel oil (3.32 m/l or 41.2 ft/US gal), and that it had a passenger capacity of 1777. Thus carrying 1777 passengers we can calculate an efficiency of 16.7 passenger miles per imperial gallon (16.9 l/100 p·km or 13.9 p·mpg–US).
MS Oasis of the Seas has a capacity of 6,296 passengers and a fuel efficiency of 14.4 passenger miles per US gallon. Voyager-class cruise ships have a capacity of 3,114 passengers and a fuel efficiency of 12.8 passenger miles per US gallon.
Emma Maersk uses a Wärtsilä-Sulzer RTA96-C, which consumes 163 g/kW·h and 13,000 kg/h. If it carries 13,000 containers then 1 kg fuel transports one container for one hour over a distance of 45 km. The ship takes 18 days from Tanjung (Singapore) to Rotterdam (Netherlands), 11 from Tanjung to Suez, and 7 from Suez to Rotterdam, which is roughly 430 hours, and has 80 MW, +30 MW. 18 days at a mean speed of 25 knots (46 km/h) gives a total distance of 10,800 nautical miles (20,000 km).
Assuming the Emma Maersk consumes diesel (as opposed to fuel oil which would be the more precise fuel) then 1 kg diesel = 1.202 litres = 0.317 US gallons. This corresponds to 46,525 kJ. Assuming a standard 14 tonnes per container (per teu) this yields 74 kJ per tonne-km at a speed of 45 kmh (24 knots).
A sailboat, much like a solar car, can locomote without consuming any fuel. A sail boat such as a Dinghy using just wind power requires no input energy in terms of fuel. However some manual energy is required by the crew to steer the boat and adjust the sails using lines. In addition energy will be needed for demands other than propulsion, such as cooking, heating or lighting. The fuel efficiency of a single-occupancy boat is highly dependent on the size of its engine, the speed at which it travels, and its displacement. With a single passenger, the equivalent energy efficiency will be lower than in a car, train, or plane.
Many seaports (e.g. container ports, cruise ports) endeavour to enhance energy efficiency. To ingrain sustainability and to achieve green seaports, many ports started harnessing renewable energy and using innovative technologies, alternative fuels (e.g. LNG, hydrogen, biofuel), smarter power distribution systems, energy consumption measurement systems. Operational strategies (e.g. peak shaving, demand side management), technology usage (e.g. electrification of equipment, cold ironing, energy storage systems), renewable energy, alternative fuels and energy management systems (e.g. smart grid with renewable energy) are gaining popularity.
International transport comparisons
European Public transport
Rail and bus are generally required to serve 'off peak' and rural services, which by their nature have lower loads than city bus routes and inter city train lines. Moreover, due to their 'walk on' ticketing it is much harder to match daily demand and passenger numbers. As a consequence, the overall load factor on UK railways is 35% or 90 people per train:
Conversely, airline services generally work on point-to-point networks between large population centres and are 'pre-book' in nature. Using yield management, overall load factors can be raised to around 70–90%. Intercity train operators have begun to use similar techniques, with loads reaching typically 71% overall for TGV services in France and a similar figure for the UK's Virgin Trains services.
US Passenger transport
The US transport Energy Data Book states the following figures for passenger transport in 2009: These are based on actual consumption of energy, at whatever occupancy rates there were.
|Transport mode||Average passengers |
|BTU per |
|MJ per |
|Rail (intercity Amtrak)||20.9||2,435||1.596|
|Rail (transit light & heavy)||24.5||2,516||1.649|
US Freight transport
|transport mode||Fuel consumption|
|BTU per short ton-mile||kJ per tonne-kilometre|
|Class 1 railroads||289||209|
|Air freight (approx.)||9,600||6,900|
From 1960 to 2010 the efficiency of air freight has increased 75%, mostly due to more efficient jet engines.
1 gal-US (3.785 l, 0.833 gal-imp) of fuel can move a ton of cargo 857 km or 462 nmi by barge, or 337 km (209 mi) by rail, or 98 km (61 mi) by truck.
- Space Shuttle used to transport freight to the other side of the Earth (see above): 40 megajoules per tonne-kilometre.
- Net energy for lifting: 10 megajoules per tonne-kilometre.
Natural Resources Canada's Office of Energy Efficiency publishes annual statistics regarding the efficiency of the entire Canadian fleet. For researchers, these fuel consumption estimates are more realistic than the fuel consumption ratings of new vehicles, as they represent the real world driving conditions, including extreme weather and traffic. The annual report is called Energy Efficiency Trends Analysis. There are dozens of tables illustrating trends in energy consumption expressed in energy per passenger km (passengers) or energy per tonne km (freight).
French environmental calculator
The environmental calculator of the French environment and energy agency (ADEME) published in 2007 using data from 2005 enables one to compare the different means of transport as regards the CO2 emissions (in terms of carbon dioxide equivalent) as well as the consumption of primary energy. In the case of an electric vehicle, the ADEME makes the assumption that 2.58 toe as primary energy are necessary for producing one toe of electricity as end energy in France (see Embodied energy#In the energy field).
This computer tool devised by the ADEME shows the importance of public transport from an environmental point of view. It highlights the primary energy consumption as well as the CO2 emissions due to transport. Due to the relatively low environmental impact of radioactive waste, compared to that of fossil fuel combustion emissions, this is not a factor in the tool. Moreover, intermodal passenger transport is probably a key to sustainable transport, by allowing people to use less polluting means of transport.
German environmental costs
|Regional rail passenger transport (MJ/pkm)||0.98|
|Long-distance rail passenger transport (MJ/pkm)||0.38|
|Bus service (MJ/pkm)||1.22|
|Rail freight transport (MJ/tkm)||0.35|
|Road freight transport (MJ/tkm)||1.31|
|Air freight (MJ/tkm)||10.46|
|Ocean freight (MJ/tkm)||0.11|
- Brake specific fuel consumption
- Fuel economy in automobiles
- Fuel economy-maximizing behaviors
- Fuel management systems
- Marine fuel management
- Thrust specific fuel consumption
- Vehicular metrics
- ACEA agreement
- Alternative propulsion
- Corporate Average Fuel Economy (CAFE)
- Emission standard
- Gasoline gallon equivalent
- Life cycle assessment
- "Efficiency". Retrieved 18 September 2016.
- Assessment of Fuel Economy Technologies for Light-duty Vehicles. The National Academies Press. 2011. doi:10.17226/12924. ISBN 978-0-309-15607-3. Retrieved 18 September 2016.
- "Glossary of energy-related terms". U.S. Department of Energy. Retrieved 20 September 2016.
- "Energy Content of Fuels (in Joules)" (PDF).
- "Calories - Joules units conversion". unitsconversion.com.ar. Retrieved 24 June 2017.
- "Energy Units". aps.org. Retrieved 24 June 2017.
- Aeroplane Efficiency, Fédération Aéronautique Internationale, "FAI – The World Air Sports Federation"
- "Calories Burned Calculator". Runner's World. 5 August 2016. Retrieved 23 June 2017.
- "Average Vehicle Occupancy by Mode and Purpose". nhts.ornl.gov. Retrieved 8 June 2018.
- "Occupancy rates of passenger vehicles". European Environment Agency. Retrieved 8 June 2018.
- Mackenzie, Brian. "Energy expenditure for walking and running".
- "Convert km/MJ to m/J - Wolfram|Alpha". wolframalpha.com. Retrieved 17 June 2018.
- "Convert kWh/100km to kilocalorie per km - Wolfram Alpha". wolframalpha.com. Retrieved 17 June 2018.
- "Convert kWh/100km to MJ/100km - Wolfram|Alpha". wolframalpha.com. Retrieved 17 June 2018.
- "Convert kWh/100km to J/m - Wolfram|Alpha". wolframalpha.com. Retrieved 17 June 2018.
- "The velomobile: high-tech bike or low-tech car?".
- "Waw:: a practical sports car :: - mobilitylab.be".
- "Calculation of conversion from dietary calories per mile to miles per gallon gasoline, using the energy density of gasoline listed by Wolfram Alpha". 2011. Retrieved 19 July 2011.
- "Mi Electric Scooter (M365)". Xiaomi. Retrieved 19 September 2018.
Power required for a single full charge (0.335kWh) ÷ typical mileage (30km)
- "MIT Unveils 90 MPH Solar Race Car". Wired. 27 February 2009.
- "Vehicle Technologies Office - Department of Energy" (PDF).
- "Vehicle details for Polo 3 / 5 Door (from Nov 06 Wk 45>) 1.4 TDI (80PS) (without A/C) with DPF BLUEMOTION M5". UK Vehicle Certification Agency. Archived from the original on 10 February 2009. Retrieved 22 March 2008.
- "Vehicle details for Ibiza ( from NOV 06 Wk 45 > ) 1.4 TDI 80PS Ecomotion M5". UK Vehicle Certification Agency. Archived from the original on 10 February 2009. Retrieved 22 March 2008.
- "2016 Best and Worst Fuel Economy Vehicles".
- "2018 Nissan Leaf". EPA. Retrieved 23 May 2018.
- "2017 Toyota Prius Eco". EPA. Retrieved 23 May 2018.
- "Miles per kwh? | Tesla". forums.tesla.com. Retrieved 8 June 2018.
- "Demonstration of Caterpillar C-10 Duel-Fuel Engines in MCI 102DL3 Commuter Buses" (PDF). National Renewable Energy Laboratory. January 2000. Retrieved 5 September 2018.
- "Passenger Transport (Fuel Consumption)". Hansard. UK House of Commons. 20 July 2005. Retrieved 25 March 2008.
- "CATALYST® : 40 FOOT BUS PERFORMANCE SPECIFICATIONS" (PDF). Proterra, Inc. May 2018. Retrieved 15 January 2019.
- "Energy Efficiency - Contribution of Urban Rail Systems" (PDF). Union internationale des transports publics. Retrieved 12 June 2018.
- JR East Annual Report 2017, JR-East Annual Report 2017
- Relatório & Contas da CP; página 16; 2012
- "Eficiência energética: carro ou comboio?".
- "Occupancy rates". European Environment Agency. Retrieved 19 June 2018.
- "European Environment Agency Occupancy Rates, page 3]" (PDF). europa.eu. Archived from the original (PDF) on 13 June 2007. Retrieved 4 March 2007.
- EPA (2007). "Appendix B, Transportation Energy Data Book". Retrieved 16 November 2010.
- "How to Convert Watts to Calories Burned While Cycling – Gear & Grit". Gear & Grit. 6 January 2017. Retrieved 27 November 2018.
- "Power vs speed calculator".
- Lemire-Elmore, Justin (13 April 2004). "The Energy Cost of Electric and Human-Powered Bicycles" (PDF). ebikes.ca.
- "Oak Ridge National Laboratory (ORNL)". Archived from the original on 27 September 2011.
- "Vehicle Technologies Office - Department of Energy" (PDF).
- Maps and Data Archived 12 June 2007 at the Wayback Machine – Metropolitan Transportation Commission for the nine-county San Francisco Bay Area, California
- "Transport trends: current edition". UK Department for Transport. 8 January 2008. Archived from the original on 22 April 2008. Retrieved 23 March 2008.
- (fr) Life cycle assessment website www.ademe.fr see page 9
- Beusen; et al. (2009). "Using on-board logging devices to study the long-term impact of an eco-driving course". Transportation Research D. 14 (7): 514–520. doi:10.1016/j.trd.2009.05.009.
- "Do lower speed limits on motorways reduce fuel consumption and pollutant emissions?". Retrieved 12 August 2013.
- "Vehicle Technologies Office - Department of Energy" (PDF).
- "Best on CO
2 rankings". UK Department for Transport. Archived from the original on 12 March 2008. Retrieved 2008-03-22.
- Jerry Garrett (27 August 2006). "The Once and Future Mileage King". The New York Times.
- "2017 Honda Civic 4DR". EPA. Retrieved 24 May 2018.
- "2017 Mitsubishi mirage". EPA. Retrieved 24 May 2018.
- "2017 Hyundai Ioniq". EPA. Retrieved 23 May 2018.
- "2017 Hyundai Ioniq Electric". EPA. Retrieved 23 May 2018.
- "Fuel-Efficiency of Travel in the 20th Century: Appendix-Notes".
- Fuel Efficiency of Travel in the 20th Century)
- "Commission for integrated transport, Short haul air v High speed rail". Archived from the original on 26 April 2007.
- Railway handbook: Energy consumption and CO
2 emissions website of the International Union of Railways (UIC, based in Paris); see figure 15 on page 27, and values on page 86. This document is the result of a joint work between UIC and International Energy Agency (IEA, based in Paris)
- Tracking clean energy progress website iea.org
- "Rail News August 2016 - For Railroad Career Professionals From Progressive Railroading magazine".
- "The Economic Impact of America's Freight Railroads" (PDF). Association of American Railroads. July 2019. p. 2.
- "Freight On Rail" (PDF). freightonrail.org.uk.
- ""复兴号"上的黑科技:往返一趟京沪省电5000度". news.sina.com.cn. 28 September 2017. Retrieved 14 May 2018.
- Environmental Goals and Results, JR-East Sustainability Report 2005
- JR East Group CSR 2017, JR-East Sustainability Report 2017
- TGV Duplex assuming 3 intermediate stops between Paris and Lyon.
- Estimating Emissions from Railway Traffic Archived 6 December 2006 at the Wayback Machine 6 December 2006 at the Wayback Machine. , page 74
- Colorado Railcar double-deck DMU hauling two Bombardier Bi-level coaches
- Colorado Railcar: "DMU Performs Flawlessly on Tri-Rail Service Test" Archived 19 March 2007 at the Wayback Machine
- SBB Facts and Figures Traffic Archived 16 May 2012 at the Wayback Machine
- Combino – Low Floor Light Rail Vehicles Tests, Trials and Tangible Results[permanent dead link]
- Davis, Stacy C.; Susan W. Diegel; Robert G. Boundy (2011). Transportation Energy Data Book: Edition 30. US Department of Energy. pp. Table 2.14. ORNL-6986 (Edition 30 of ORNL-5198). Retrieved 22 February 2012.
- Bus and Rail Final Report[dead link]
- "Van Hool presents the ExquiCity Design Mettis". Archived from the original on 5 June 2013. Retrieved 5 June 2012.
- Seara.com. "Indicadores de Atividade".
- "Crawler-Transporter System".
- Barney L. Capehart (2007). Encyclopedia of Energy Engineering and Technology, Volume 1. CRC Press. ISBN 0-8493-3653-8, ISBN 978-0-8493-3653-9.
- "Powerplant." concordesst.com. Retrieved: 2 December 2009.
- "Technical Specifications: Boeing 747-400". Boeing. Retrieved 11 January 2010.
- "National Aerospace Laboratory]" (PDF). transportenvironment.org.
- Peeters P.M., Middel J., Hoolhorst A. (2005). Fuel efficiency of commercial aircraft An overview of historical and future trends. National Aerospace Laboratory, The Netherlands.
- "The A380: The future of flying". Airbus. Archived from the original on 14 December 2007. Retrieved 2008-03-22.
- Bradley, Grant (17 November 2009). "'Shark fin' wings give airline chiefs something to smile about". NZ Herald – via New Zealand Herald.
- "A320 plane shark fins small winglets successfully completed the first flight test".
- "Minix wing tip device promises 6% gain in fuel efficiency for airliners".
- Ecogeek Article Archived 14 July 2014 at the Wayback Machine
- "Boeing to Begin Ground Testing of X-48B Blended Wing Body Concept." Archived 19 August 2012 at the Wayback Machine Boeing, 27 October 2006. Retrieved: 10 April 2012.
- Lorenz III, Phillip. "AEDC testing brings unique blended wing aircraft closer to flight." Archived 14 July 2014 at the Wayback Machine AEDC, U.S. Air Force, 3 July 2007. Retrieved: 10 April 2012.
- Mahony, Melissa. "A sharkskin coating for ships, planes and blades - ZDNet".
- Spakovszky, Zoltan (2009). "Unified Propulsion Lecture 1". Unified Engineering Lecture Notes. MIT. Retrieved 3 April 2009.
- US application 2009020643, Airbus & Christophe Cros, "Aircraft having reduced environmental impact", published 2009-01-22
- Contact, Experimental Aircraft and Powerplant Newsforum for Designers and Builders, Issue 55, March–April 2000
- "Tecnam P92 Echo Classic". Tecnam costruzioni aeronautiche s.r.l. Archived from the original on 29 May 2012. Retrieved 22 May 2012.
- "Tecnam P2002 Sierra De Luxe". Tecnam costruzioni aeronautiche s.r.l. Archived from the original on 8 June 2012. Retrieved 22 May 2012.
- "Queen Elizabeth 2: Technical Information" (PDF). Cunard Line. Archived from the original (PDF) on 18 March 2009. Retrieved 2008-03-31.
- "Cruise Ship Gas Mileage". 27 December 2010.
- Emma Mærsk schedules Mærsk, 5 December 2011.
- A review of energy efficiency in ports: Operational strategies, technologies and energy management systems "Renewable and Sustainable Energy Reviews, 2019"
- "Delivering a sustainable railway - Publications - GOV.UK". Archived from the original on 5 September 2007. Retrieved 25 July 2007.
- "Energy & Emissions Statement" (PDF).
- Defra 2008 Guidelines to Defra’s GHG Conversion Factors Archived 5 January 2012 at the Wayback Machine 5 January 2012 at the Wayback Machine.
- "Kilograms of CO2 per passenger kilometre for different modes of transport within the UK]" (PDF). aef.org.uk.
- US Environmental protection, 2006 Archived 12 February 2009 at the Wayback Machine
- Energy Efficiency – Transportation sector Archived 22 September 2008 at the Wayback Machine (from the United States Department of Energy's Energy Information Administration)
- Energy Table 2.15
- "Trends in Fuel Efficiency, Selected Passenger Jet Planes".
- Rodrigue, Dr. Jean-Paul (7 December 2017). "Transportation and Energy".
- "2010 data". Oee.rncan.gc.ca. Retrieved 19 June 2018.
- (fr) ADEME environmental calculator Archived 20 July 2011 at the Wayback Machine which informs about the CO2 emissions and the primary energy consumption
- "Energy efficiency increased | Deutsche Bahn AG". ib.deutschebahn.com. Retrieved 8 June 2019.