The ATASCII character set, from ATARI Standard Code for Information Interchange, alternatively ATARI ASCII, is the variation on ASCII used in the Atari 8-bit family of home computers. The first of this family were the Atari 400 and 800, released in 1979, and later models were released throughout the 1980s. The last computer to use the ATASCII character set was the Atari XEGS which was released in 1987. The Atari ST family of computers used the different Atari ST character set.
Like most other non-standard ASCIIs, ATASCII has its own special block graphics symbols (arrows, blocks, circles, line segments, playing card suits, etc.) corresponding to the control character locations of the standard ASCII table (characters 0–31), and a few other character locations.
The most notable difference between standard ASCII and ATASCII is the use of control characters. In standard ASCII, a character in the range 0 to 31 is construed as a command, which might move the cursor, clear the screen, end a line, and so on. Some of these were designed for use on printers and teletypes rather than on screen (to advance the paper, overtype, and so on). In ATASCII most of the ASCII control character values produce a graphics glyph instead. ATASCII uses character values different from ASCII for cursor control.
ATASCII has a character set of only 128 characters. If the high-order bit is set on a character (i.e., if the byte value of the character is between 128 and 255) the character is generally rendered in the reverse video (also called "inverse video") of its counterpart between 0 and 127, using a bitwise negation of the character's glyph. This is done by the ANTIC chip. The two exceptions to this rule are that an "escape" character (ATASCII and ASCII 27) with its high order bit set becomes an "EOL" or "End Of Line" character (ATASCII 155; ASCII 13), and a "clear screen" character (ATASCII 125) with its high order bit set becomes a "bell" or "buzzer" character (ATASCII 253; ASCII 7). No Atari printers actually have a bell, but the computer will sound if it is written to the screen device.
The ATASCII control characters used by the screen editor for cursor control (arrow keys) and text editing (tab, insert, delete, backspace, etc.) have associated graphic symbols that can be displayed by preceding them by the "escape" character (ATASCII 27). For example, a right arrow can be displayed on a screen or printer by preceding it with the escape character followed by the "cursor right" character itself (ATASCII 31).
The Atari screen editor implements the text cursor by simply inverting the character at the cursor position (by XOR with $80). It does not flash.
The differences between character representation can cause problems during modem communication between Ataris and other computers. Cursor movement commands (and even carriage returns and line feeds) from computers not using ATASCII will be nonsense on an Atari, and vice versa. Terminal programs need to translate between ATASCII and standard ASCII.
Some Atari-based BBSs exploited this difference by asking the client to hit the "Return" key. If it got 13 (ASCII CR), then standard ASCII would be used. If it got 155 (ATASCII CR) it would switch to ATASCII, allowing full use of the ATASCII graphic set. Some Atari BBSs would also block features (or even block access completely) for non-Atari users.
The control codes in ATASCII are transmissible to other computers such as BBS's, and crude animations are possible. These animations, also known as "break movies", often take the form of short cartoons, and were a popular feature of Atari BBSs in its heyday.
Because cursor control operations are represented with a single character (as opposed to multi-byte 'escape' sequences that were common in other schemes, like ANSI or VT100), it is quite easy to make these animations. They can be created by a short BASIC program that captures keyboard commands, echoes them to the screen and saves them to a file. The Atari also allowed commands to be typed and captured as part of its operating system. Of course this required care to get it right, but after a few attempts it normally became quite easy. The simple capture programs didn't have editing features, so ATASCII movies frequently had errors that were corrected by repositioning the cursor and printing over the mistake (a computer version of correction fluid).
The following table shows the glyphs for ATASCII characters and the corresponding Unicode glyph. Characters without a corresponding Unicode glyph are represented by abbreviations for their names.
|8_||♥ ||├ ||▊ |
|┘ ||┤ ||┐ ||╱ ||╲ ||◤ |
|9_||♣ ||┌ ||─ ||┼ ||● ||▀ |
|▎ ||┬ ||┴ ||▐ |
|└ ||NBSP/LF |
|↑ ||↓ ||← ||→|
|! ||" ||# ||$ ||% ||& ||' ||( ||) ||* ||+ ||, ||- ||. ||/|
|B_||0 ||1 ||2 ||3 ||4 ||5 ||6 ||7 ||8 ||9 ||: ||; ||< ||189 ||> ||?|
|C_||@ ||A ||B ||C ||D ||E ||F ||G ||H ||I ||J ||K ||L ||M ||N ||O|
|D_||P ||Q ||R ||S ||T ||U ||V ||W ||X ||Y ||Z ||[ ||\ ||] ||^ ||_|
|E_||♦ ||a ||b ||c ||d ||e ||f ||g ||h ||i ||j ||k ||l ||m ||n ||o|
|F_||p ||q ||r ||s ||t ||u ||v ||w ||x ||y ||z ||♠ ||- ||↰/BEL |
- Actually an upper ¼ block
- Characters 1B-1F and 7D-7F had a dual use as graphics characters and control characters.
Note the asymmetry in the selection of graphics characters: There are lower triangles but no upper triangles, a left half block but no right half block, and a lower half block but no upper half block. These missing characters could be displayed by using inverse video.
The glyph representation in ROM used by ANTIC for display are assigned in different order from ASCII/ATASCII. For example, to display the characters "@ABC" on screen by writing directly to the screen memory, one would write the decimal values 32, 33, 34, and 35 rather than the ASCII/ATASCII values 64, 65, 66, and 67.
|125||Clear Screen||CTRL+< or ⇧ Shift+<|
|155||End of line||RETURN|
|156||Delete Line||⇧ Shift+← Backspace|
|157||Insert Line||⇧ Shift+>|
|158||Clear Tab stop||CTRL+Tab ↹|
|159||Set Tab stop||⇧ Shift+Tab ↹|
|254||Delete Character||CTRL+← Backspace|
- ATASCII concise graphical overview (4.2KB GIF image)
- ATASCII <–> IBM ASCII tables (mostly plain ASCII text)
- ATASCII Character Sets
- Typography in 8 bits: System fonts
- Mac/Atari Fusion: Atari Fonts (3 fonts in varying levels of smoothness, TrueType cross-platform format for replicating ATASCII characters on modern computers)